ITI Concord - Arming Always Silent; Adjusting the Touchpad Beeps (Fixed Display Touchpad Only); Adjusting the System Status Voice Volume; Adjusting the Touchpad Display Brightness

14
Arming Always Silent
Turning this feature on in User Programming means that
the status beeps that come from touchpads and interior
speakers while arming will always be silent. You will not
have to enter
5
before arming, as with Silent Arming on
Demand.
To enable Silent Arming:
1. Enter the programming menus by pressing
9
+ System or Partition Master
CODE
.
2. Press
041
.
3. To turn Silent Arming:
• on, press
2
+
ƒ
. No system status beeps
will sound while arming.
• off, press
1
+
ƒ
. System status beeps will
sound from touchpad while arming.
4. Press
‚
+
00
+
ƒ
to exit the programming
menus.
Adjusting the Touchpad Beeps (Fixed Display
Touchpad Only)
The frequency or pitch of chime and trouble beeps from
each fixed display touchpad can be adjusted individually
to a more desirable or distinct tone.
Chime and trouble beep tones sound using the default
frequency during, or within 15 seconds of any button
activity at that specific touchpad.
To change status tone pitch:
1. Press and hold
‚
+
0
until you hear a steady
tone, then release the buttons.
2. Press and hold
1
to lower the pitch or press and
hold
2
to raise the pitch.
3. Release the button when the desired pitch is
heard.
After about 15 seconds of no touchpad activity, the
steady tone stops sounding.
Adjusting the System Status Voice Volume
If you have an optional voice module installed, you may
want to adjust the volume at which system status mes-
sages are announced.
To change the voice volume:
1. Enter the programming menus by pressing
9
+ System or Partition Master
CODE
.
2. Press
043
.
3. Select a volume level
1
–
7
(7 being the
loudest) and press
ƒ
.
4. Press
‚
+
00
+
ƒ
to exit the programming
menus.
Adjusting the Touchpad Display Brightness
You may want to change the brightness of a touchpad dis-
play based on its location in a building or room. For
example, dim the touchpad display in a bedroom or
enhance a display near a window.
Changing the touchpad display affects only the touchpad
currently being used.
To change touchpad display brightness:
1. Enter the programming menus by pressing
9
+ System or Partition Master
CODE
.
2. Press
042
.
3. Select a brightness level:
•
0
+
ƒ
Off
•
1
+
ƒ
Low
•
2
+
ƒ
Medium
•
3
+
ƒ
High
4. Press
‚
+
00
+
ƒ
to exit the programming
menus.
After dimming the display, pressing any button momen-
tarily returns the display to full brightness. After 15 sec-
onds without touchpad activity, the display returns to the
set dimmed level. If an alarm occurs while the display is
dimmed, it automatically returns to the full brightness
level and stays that way until you disarm your system.
Adjusting the Volume of the Wireless Siren
(Not investigated by UL) Your system may
include a wireless siren that may be super-
vised or unsupervised.
The system can supervise the state of the siren
to make sure that it is plugged into the outlet.
In addition to Police, Fire, and Auxiliary
alarms, the wireless siren will sound trouble beeps in the
event of a trouble condition anywhere in the system, and
emit arming status beeps during Entry and Exit Delay peri-
ods.
The wireless siren has five volume levels from 0 (silent) to
4 (loudest). All alarms sound at the loudest level, regard-
less of the volume setting.
To change the volume of the wireless siren:
1. Hold down the button on the front of the siren for
ten seconds until it beeps, then release it.
The siren responds by beeping once, indicating it
has entered change volume mode.
2. To increase the volume by one level, press the
siren button for one second until it beeps. Repeat
until the volume reaches the desired level.
3. After the highest level, the siren sounds one long
beep, followed by 4 short beeps to signal the silent
level. It then cycles through the levels again.
Silent
2
1
3
4