13
Assigning the System Test Attribute
System Test is a user code attribute that allows the user to
perform system tests. If the user code does not have this
attribute turned on, the user will not be able to perform
phone or sensor tests.
To assign System Testing to a user:
1. Enter the programming menus by pressing
9
+ System or Partition Master
CODE
.
2. Press
030
nn
4
where nn is user 00
through 59.
3. To turn System Testing:
• on, press
2
+
ƒ
.
• off, press
1
+
ƒ
.
4. Press
‚
+
00
+
ƒ
to exit the programming
menus.
Assigning the Latchkey Report Attribute
Latchkey Report is a user code attribute that causes the
panel to send a message to a pager when the user
changes system arming levels. See “Latchkey Paging” on
page 21.
To assign Latchkey Report to a user:
1. Enter the programming menus by pressing
9
+ System or Partition Master
CODE
.
2. Press
030
nn
5
where nn is user 00
through 59.
3. To turn Latchkey Report:
• on, press
2
+
ƒ
.
• off, press
1
+
ƒ
.
4. Press
‚
+
00
+
ƒ
to exit the programming
menus.
S
ECTION
7:
S
ETTING
THE
T
IME
AND
D
ATE
Although the installer usually sets the time and date at the
time of installation, the user can change it when neces-
sary.
To set the System Time:
1. Enter the programming menus by pressing
9
+ System or Partition Master
CODE
.
2. Press
020
.
3. Enter the correct time in 24-hour format (4 digits),
then press
ƒ
.
For example, if the current time is 7:23 a.m.,
press
0723
+
ƒ
.
4. Press
‚
+
00
+
ƒ
to exit the programming
menus.
To set the System Date:
1. Enter the programming menus by pressing
9
+ System or Partition Master
CODE
.
2. Press
021
.
3. Enter the current date as 6 digits (mm/dd/yy) then
press
ƒ
.
For example, if the current date is January 15,
2000, press
011500
+
ƒ
.
4. Press
‚
+
00
+
ƒ
to exit the programming
menus.
S
ECTION
8:
A
DJUSTING
S
YSTEM
S
OUNDS
AND
T
OUCHPAD
B
RIGHTNESS
Arming Your System Silently
Use the Silent Arming feature to arm your system without
disturbing people throughout the house with arming sta-
tus beeps. There are two methods for implementing
Silent Arming:
•Silent on Demand.
(User presses
5
before arming.)
• Arming Always Silent (Silent Arming feature on).
Regardless of the method employed, when Silent Arming
is in effect, no Exit beeps sound.
Silent Arming on Demand
Pressing
5
before arming silences arming status beeps
from touchpads and interior sirens for only the current
arming period.
To use Silent Arming on demand:
1. From any touchpad, press
5
.
2. Within 4 seconds enter:
2
+
CODE
or
3
+
CODE
.
Note: If Quick Arm feature is on, an access code is not
required. See page 6 for more information.
00:00
01:00
02:00
03:00
04:00
05:00
06:00
07:00
24-Hour Form at
08:00
09:00
10:00
11:00
12:00
13:00
14:00
15:00
8:00 am
9:00 am
10:00 am
11:00 am
Noon
1:00 pm
2:00 pm
3:00 pm
16:00
17:00
18:00
19:00
20:00
21:00
22:00
23:59
4:00 pm
5:00 pm
6:00 pm
7:00 pm
8:00 pm
9:00 pm
10:00 pm
11:59 pm
Midnight
1:00 am
2:00 am
3:00 am
4:00 am
5:00 am
6:00 am
7:00 am
To Next Page
