ITI Concord - Sending a Police Panic Alarm; Phone Questions?; What if someone calls while Im operating the panel?; Can I control the system while Im talking on the phone?

28
Sending a Police Panic Alarm
Your system can be set up so that you can send a Police
panic alarm from a Touchtone phone. If your system is
set up to send a Police panic alarm:
•Use the
‚
, regardless of your phone command key.
• Do not wait more than two seconds between key-
presses. Continue pressing
‚
even if you hear the sys-
tem voice interrupt with a system status.
• Police panic alarms can be activated from a Touchtone
phone on the premises only. The alarm cannot be acti-
vated from an off-site phone.
Step 2. Enter the command.
Disarm the
system
ƒ
+
1
+
CODE
Arm to Level 2*
ƒ
+
2
+
CODE
Arm to Level 3*
ƒ
+
3
+
CODE
Send a Police
panic alarm
‚
+
‚
+
‚
+
‚
+
‚
+
‚
(Available from on-site only.)
Arm system with
No Delay*
ƒ
+
2
+
CODE
+
4
or
ƒ
+
3
+
CODE
+
4
Arm to enable
Latchkey*
ƒ
+
2
+
CODE
+
6
or
ƒ
+
3
+
CODE
+
6
Arm system with
exit lights off*
ƒ
+
2
+
CODE
+
0
or
ƒ
+
3
+
CODE
+
0
Bypass a sensor
Indirectly: Arm system +
ƒ
+
ƒ
Directly:
ƒ
+
ƒ
+
CODE
+ Sensor Number
Arm silently*
ƒ
+
5
+
2
+
CODE
or
ƒ
+
5
+
3
+
CODE
Turn all lights
on/off
ƒ
+
0
+
0
Turn specific
lights on/off
ƒ
+
0
+ Light number (1–9)
Cancel an
accidental alarm
ƒ
+
1
+
CODE
Check the
system status
ƒ
+ for short status
ƒ
+
‚‚
for full status
Turn Chime
on/off
ƒ
+
7
+
1
Turn Energy
Saver on/off
ƒ
+
7
+
2
Disable local
phone access
ƒ
+
7
+
3
(on-site only) or
Wait 5 seconds after picking up a
local phone.
Check alarm
memory
ƒ
+
7
+
6
Activate
Outputs
ƒ
+
7
+
7
+
Output number (1–6)
*If Quick Arm feature is on, access code is not required. See page 6
for more information.
Phone Questions ?
What if someone calls
while I’m operating the panel?
If the phone rings while you’re using it to operate the
system, you’ll hear one long beep for each ring from
interior speakers and phones. You can answer the call
by simply hanging up on the system, then answering
the call as you normally would.
You’ll have to initiate another session to resume opera-
tion.
Can I control the system while I’m
talking on the phone?
No.
How do I perform other phone
operations without commanding
my security system?
You can use your phone for transactions such as bank-
ing from home by temporarily disengaging phone con-
trol to your security system. The commands described
below work for one call at a time.
To disengage local phone control:
•Enter
ƒ
+
7
+
3
.
The system responds by returning a dial tone.
• Pick up the phone receiver and wait 5 seconds
before dialing any numbers. After the 5 second
period, the system disables local phone control
and ignores phone commands.