ITI Concord - Page 46

42
To erase a user code:
1. Enter the programming menus by pressing
9
+ System or Partition Master
CODE.
2. Press
B
until the touchpad displays “USER
CODES,” then press
ƒ
.
3. The touchpad displays “REGULAR USER CODES”
or “REG CODES.” Press
ƒ
. (You cannot delete
the System Master code.)
4. Press
B
until the touchpad displays the user code
you wish to erase, then press
ƒ
. For example, if
you want to change User code 4, press
ƒ
when
the touchpad displays “USER 04” or “REG CODE
04.”
5. Enter the System or Partition Master code you
used in Step 1 and press
ƒ
. The deleted code
appears as “USER 04 ****” or “RG 01 ––––,” for
example.
6. Press
‚
+
B
to move to the next user code, or
‚
+
00
+
ƒ
to exit the programming
menus.
To change or delete the Partition Master Code:
1. Enter the programming menus by pressing
9
+ System or Partition Master
CODE.
2. Press
B
until the touchpad displays “USER
CODES,” then press
ƒ
.
3. The touchpad displays “REGULAR USER CODES”
or “REG CODES.” Press
B
until the display reads
“PARTITION MASTER CODE” or “PTN MASTER,”
then press
ƒ
.
4. Enter the System Master Code to delete the exist-
ing Partition Master Code
OR enter a new 4 digit Partition Master Code to
replace the existing code, then press
ƒ
.
5. Press
‚
+
00
+
ƒ
to exit the programming
menus.
To change the Master Code:
1. Enter the programming menus by pressing
9
+ System Master
CODE
.
2. Press
B
until the touchpad displays “USER
CODES,” then press
ƒ
.
3. The touchpad displays “REGULAR USER CODES”
or “REG CODES.” Press
B
until the display reads
“SYSTEM MASTER CODE” or “SYS MASTER,” then
press
ƒ
.
4. Replace the existing code with the new 4 digit
System Master Code then press
ƒ
.
5. Press
‚
+
00
+
ƒ
to exit the programming
menus.
Using Programming Shortcuts
A programming shortcut is a number that “jumps” you to
a particular spot in the programming menus.
A series of shortcut numbers takes you directly to the fea-
ture or code you want to change.
1. Enter User Programming.
Local Phone
ƒ
+
9
+
CODE
Remote Phone Access
Dial the phone number +
ƒ
+
CODE
+
ƒ
+
9
+
CODE
Touchpad
9
+
CODE
2. Enter a programming command sequence.
Time
‚
+
020
+
TTTT
+
ƒ
Date
‚
+
021
+
DDMMYY
+
ƒ
Regular User Codes
User 00:
‚
+
030000
+
NNNN
+
ƒ
User 01:
‚
+
030010
+
NNNN
+
ƒ
User 02:
‚
+
030020
+
NNNN
+
ƒ
(Continues through User 59)
User 59:
‚
+
030590
+
NNNN
+
ƒ
If using alphanumeric or fixed display touchpads, use
A
and
B
to scroll
through the code attributes and change them as required.
Partition Master Codes Partition 1:
‚
+
0310
+
NNNN
+
ƒ
Partition 2:
‚
+
0311
+
NNNN
+
ƒ
System Master Code
‚
+
0320
+
NNNN
+
ƒ
Direct Bypassing Attribute
‚
+
030NN1
+
1
(off) or
2
(on) +
ƒ
(nn = user no.)