JR XP810-3 User Manual

www.modelflight.com.au – World’s best source of JR products
3
.
1
1 Win
g
T
yp
e Selection
(
S
y
stem Set-U
p
Mode
)
Use of V - T ail
Connect the left moveable tail sur faces to the ser vo connected to
ELEV and the right moveable tail surfaces to the ser vo connected
to RUDD. At this time, the ser vo’ s operational value is
automatically set for 7
5%. An applicable channel’ s ser vo travel is
individually adjusted by each ser vo’ s dual rate settings. Ser vo
reversing is also set individually
. Neutral adjustment should be
made individually using the Sub-Trim Adjustment Function.
Use of Dual Flap
Connect the left flap to channel 6
(
FLAP
)
and the ri
g
ht flap to the
ser vo connected to channel 7 (AUX 2) of the receiver . At this
time, the Aileron to Flap Mixing Function is available for setting,
and by using the POT (dual flap aileron trim knob), both flaps
are operational as trim for aileron operations.
A
pplicable channel’ s ser vo travel and reversing switches neutral
adjustment should be made individually using the Sub-T
rim
A
djustment Function. This setting is ver y useful and allows the left
and right ailerons and both flaps to operate as flaps or ailerons.
Connect the right aileron to channel 5 (AUX2); the left flap is
connected to channel 6 (FLAP), the left aileron to channel 2
(AILE), and the right flap is ser vo connected to channel 7
(AUX 2).
Function now being
p
ro
g
rammed
Settin
g
condition
Press the UP and DN keys
simultaneously to enter/exit
the S
y
stem Set-U
p
Mode
Press the DN and Select key
s
simultaneously to access th
e
S
y
stem Mode info dis
p
la
y
To Fla
p
Channel In
p
ut
UP
DN SELECT CH CH CLEAR
Press to reset
Selection function
To Model Data
Transfer function
Press either
CH key to
select V-Tail
or Dual Fla
p
Press + or -
key to inhibit
or activate
function
to INH
3
.
1
2 In
p
ut Selection
(
S
y
stem Set-U
p
Mode
)
A
t this time, activate dual flaps using the Flap Channel Input
Selection for FLP .SW + P6 (flap switch and flap POT set for trim
operations).
The following mixes are now available:
• flap to elevator mixing
• flap to aileron mixing
• aileron to flap mixing
• butter fly mixing
FLAP (6-ch) and AUX 2 (7-ch) ser vo travel can be adjusted by
Channel 7's travel adjust operational value.
T rim adjustment for each control sur face can be adjusted by the
following POT s: POT -5 for aileron’ s flap trim, POT -6 for flap’ s flap
trim, POT -7 for flap’ s aileron trim
Flap channel input is selectable either by flap knob (POT -6) or
flap switch. POT -6 also operates as the trim.
Selection is made by pressing either the + or - keys (POT -6—-
FLP .SW + P6). Press the CLR key to preset to POT-6 .
• When POT -6 is selected, the ser vo is 1 00% operational by the
flap knob.
• When FLP .SW+P6 is selected, flap operation is activated with
the spoiler stick (throttle stick).
• Flap ser vo travel adjustment is achieved with Flap T ravel
A
d
j
ustment.
GLID 112

JR XP810-3 Specifications

General

Brand	JR
Model	XP810-3
Category	Remote Control
Language	English