JVC SR-HD2700E - Page 27

Setting “TIME CODE DISPLAY POSITION
”
1 Press the [SET UP] button on the remote control unit
0
The Settings menu screen appears.
.
5'.'%6
':+6
&'(#7.65'66+0)
$7<<'4176276
37+%-56#4672
2#0'.&+52.#;$4+)*60'55
%.1%-5'6&+52.#;
4'/16'%10641.
4'/16'%10641.%1&'
1((
1((
#761219'41((
5'672
4'6740
5'672
1-
2
Press the [ I ] button, and select “SDI/HDMI
CONNECTION”
0
The “SDI/HDMI CONNECTION” screen appears.
.
.%*4%*
.%*4%*
5'672
4'6740
1-
5'.'%6
':+6
&+5%5'%74+6;5'66+0)
.19'4.'(6
(4#/'5;0%*410+<'4
10
10
6+/'%1&'&+52.#;215+6+10
6+/'%1&'+02765'66+0)
5&+4'%.1%-
*&/+
*&/++0276#7&+15'66+0)
5&+#7&+11762765'66+0)
5&+#7&+1+02765'66+0)
5&+*&/+%100'%6+10
1((
3
Press the [ J ] or the [ K
] button, select “TIME
CODE DISPLAY POSITION”, and press the [OK]
button
.
10
*&/+
.%*4%*
.%*4%*
4'6740
5'672
1-
5'.'%6
':+6
&+5%5'%74+6;5'66+0)
.19'4.'(6
1((
6+/'%1&'+02765'66+0)
(4#/'5;0%*410+<'4
10
10
6+/'%1&'&+52.#;215+6+10
5&+4'%.1%-
*&/++0276#7&+15'66+0)
5&+#7&+11762765'66+0)
5&+#7&+1+02765'66+0)
5&+*&/+%100'%6+10
4
Press the [ J ] or the [ K
] button to select the
display position
.
*&/+
.%*4%*
.%*4%*
4'6740
5'672
1-
5'.'%6
':+6
&+5%5'%74+6;5'66+0)
.19'4.'(6
1((
6+/'%1&'+02765'66+0)
(4#/'5;0%*410+<'4
10
10
6+/'%1&'&+52.#;215+6+10
5&+4'%.1%-
*&/++0276#7&+15'66+0)
5&+#7&+11762765'66+0)
5&+#7&+1+02765'66+0)
5&+*&/+%100'%6+10
%'06'4
722'44+)*6
722'4.'(6
.19'44+)*6
.19'4.'(6
LOWER
LEFT
: Sets
the time code display position to the bottom
left.
LOWER
RIGHT
: Sets the time code display position to the bottom
right.
UPPER
LEFT
: Sets the time code display position to the top left.
UPPER
RIGHT
: Sets the time code display position to the top
right.
CENTER: Sets the time code display position to the center.
5
Press the
[OK] button after making a selection
0
The time code display position is saved.
Memo :
0
Setting is now complete. If multiple time code inputs are not
detected from the SDI signals, time code is displayed as
“TC--:--:--:--”.
0
If
you have not set a date after selecting “DATE & TIME” and
completing the setting, time code will be displayed as
“--:--:--:--”.
0
Time
code is not displayed when the monitor is connected to
the [SDI OUT THROUGH] terminal.
Setting the Time Code
27
Preparation