KEB COMBIVERT F5 Servo User Manual

1111
18.05.04KEB COMBIVERT F5-M / S
Name: Basis
1
Introduction
General
© KEB Antriebstechnik, 2002
All Rights reserved
Chapter Section PageDate
6.9.4 Timer and Counter ............................................................ 6.9.11
6.9.5 Brake Control .................................................................... 6.9.15
6.9.6 Power-Off Function............................................................6.9.19
6.9.7 Wobbel Function ...............................................................6.9.27
6.9.8 Diameter Correction .......................................................... 6.9.29
6.9.9 Positioning Function.......................................................... 6.9.31
6.9.10 Analog setting of parameter values ................................... 6.9.34
6.10 Encoder Interface ............................................................................. 6.10.3
6.10.1 Designs .............................................................................6.10.3
6.10.2 Encoder Interface Channel 1 (X3A)................................... 6.10.4
6.10.3 Encoder Inteface Channel 2 (X3B) .................................... 6.10.5
6.10.4 Power Supply of Encoder .................................................. 6.10.7
6.10.5 Selection of Encoder ......................................................... 6.10.8
6.10.6 Basic Setting ................................................................... 6.10.10
6.10.7 Additional Parameters ..................................................... 6.10.13
6.10.8 Used Parameters............................................................. 6.10.14
6.11 Positioning and Synchronous Control........................................... 6.11.3
6.11.1 Synchronous Control......................................................... 6.11.3
6.11.2 Slave Correction................................................................ 6.11.4
6.11.3 Position Controller ............................................................. 6.11.5
6.11.4 Position Display ................................................................ 6.11.5
6.11.5 Reference Point Approach ................................................6.11.6
6.11.6 Reference Point Approach - Examples.............................. 6.11.9
6.11.7 Posi Control..................................................................... 6.11.12
6.11.8 Position scan ................................................................... 6.11.17
6.11.9 Teach Mode..................................................................... 6.11.18
6.11.10 Contouring Mode ........................................................... 6.11.19
6.11.11 Used Parameters............................................................. 6.11.20
6.12 Technology Controller ..................................................................... 6.12.3
6.12.1 The PID Controller ............................................................ 6.12.3
6.12.2 PID Setpoint Value ............................................................6.12.5
6.12.3 PID Actual Value ............................................................... 6.12.6
6.12.4 Sample Applications ......................................................... 6.12.7
6.12.5 Used Parameters............................................................. 6.12.10
6.13 CP-Parameter Definition .................................................................. 6.13.3
6.13.1 Survey ............................................................................... 6.13.3
6.13.2 Assignment of CP-Parameters .......................................... 6.13.4
6.13.3 Example ............................................................................ 6.13.5
6.13.4 Display Standardization ....................................................6.13.6
6.13.5 Used Parameters............................................................... 6.13.8
7. Start-up .......................................................................................................... 7.1.3
7.1 Preparatory Measures........................................................................ 7.1.3
7.1.1 After unpacking the Goods ..................................................7.1.3
7.1.2 Installation and Connection................................................. 7.1.3
7.1.3 Checklist prior to Start-up .................................................... 7.1.4
7.2 Initial Start-up...................................................................................... 7.2.3

KEB COMBIVERT F5 Servo Specifications

General

Brand	KEB
Model	COMBIVERT F5 Servo
Category	DC Drives
Language	English