KEB COMBIVERT F5 Servo User Manual

11 9
18.05.04KEB COMBIVERT F5-M / S
Name: Basis
1
Introduction
General
© KEB Antriebstechnik, 2002
All Rights reserved
Chapter Section PageDate
6.2.12 Analog Output / Functions (An.31/An.36/An.41) ............... 6.2.11
6.2.13 Analog Output / Display..................................................... 6.2.12
6.2.14 Gain of Output Characteristic............................................. 6.2.12
6.2.15 Period ANOUT3 (An.46).................................................... 6.2.13
6.2.16 ANOUT 1...4 Digital Settings (An.32/37/42/48) ................. 6.2.13
6.2.17 Used Parameters.............................................................. 6.2.14
6.3 Digital In- and Outputs .......................................................................... 6.3.3
6.3.1 Summary Description Digital Inputs .................................... 6.3.3
6.3.2 Input Signals PNP / NPN (di.0) ........................................... 6.3.3
6.3.3 Setting of Digital Inputs by Software (di.1, di.2) ................... 6.3.4
6.3.4 Terminal Status (ru.21) ........................................................ 6.3.5
6.3.5 Digital Filter (di.3) ................................................................ 6.3.5
6.3.6 Inversion of Inputs (di.4) ...................................................... 6.3.5
6.3.7 Edge-triggering (di.5)........................................................... 6.3.5
6.3.8 Strobe-dependent Inputs (di.6, di.7, di.8) ............................. 6.3.6
6.3.9 Input Status (ru.22) ..............................................................6.3.8
6.3.10 Reset/Input Selection and Edge Evaluation (di.9 / di.10) .... 6.3.8
6.3.11 Assignment of the Inputs ..................................................... 6.3.8
6.3.12 Summary Description - Digital Outputs.............................. 6.3.11
6.3.13 Output Signals................................................................... 6.3.12
6.3.14 Output filter (do.43, do.44)..................................................6.3.12
6.3.15 Switching Conditions (do.0...do.7) ..................................... 6.3.13
6.3.16 Inverting of Switching Conditions for Flags (do.8...do.15).. 6.3.16
6.3.17 Selection of Switching Conditions for Flags (do.16...do.23)6.3.16
6.3.18 Linking the Switching Conditions for Flags (do.24) ........... 6.3.16
6.3.19 Inverting of Flags (do.25...do.32) ....................................... 6.3.17
6.3.20 Selection of Flags (do.33...do.40) ...................................... 6.3.17
6.3.21 Linking the Flags (do.41) ................................................... 6.3.17
6.3.22 Inversion of Outputs (do.42)............................................... 6.3.18
6.3.23 Output Terminal Status (ru.25) ........................................... 6.3.18
6.3.24 Hardware output allocation (do.51).................................... 6.3.18
6.3.25 Programming Example......................................................6.3.19
6.3.26 Used Parameters............................................................... 6.3.20
6.4 Setpoint-, Rotation- and Ramp Adjustment ..................................... 6.4.3
6.4.1 Brief Description.................................................................. 6.4.3
6.4.2 Reference source oP.0 ........................................................ 6.4.4
6.4.3 Rotation Source oP.1 ........................................................... 6.4.6
6.4.4 Fixed values (oP.18...23) ..................................................... 6.4.9
6.4.5 Setpoint Limits...................................................................6.4.11
6.4.6 Setpoint Calculation .......................................................... 6.4.12
6.4.7 Ramp generator ................................................................ 6.4.13
6.4.8 Limiter (oP.40 / oP.41) ........................................................ 6.4.15
6.4.9 Ramp with constant time ................................................... 6.4.15
6.4.9 Used Parameters............................................................... 6.4.18
6.5 Voltage-/Frequency Characteristic Adjustment............................... 6.5.3
6.5.1 Control Type (ud.2) and Max Frequency Mode (only F5-B).. 6.5.3

KEB COMBIVERT F5 Servo Specifications

General

Brand	KEB
Model	COMBIVERT F5 Servo
Category	DC Drives
Language	English