Keithley 237

K
Keypad, 1-15
L
Level, 2-61
Line cycle integration, 3-83
Line Frequency, 1-20, 2-4
Line Fuse, 1-17,
2-3
Line Voltage, 1-16,1-19, 2-3
Linear Staircase Pulse Sweep, 2-58, 2-72, 3-52
Linear Staircase Pulse Sweep
Parameters,
2-65
Linear Staircase Sweep, 2-55, 2-68, 3-49
Linear Staircase Sweep Parameters, 2-64
Listen, 3-5
Local,
1-14, 3-5, 3-6
Local Lockout, 3-6
Local Sense, 3-45
Log Cannot Cross Zero, 3-64
Logarithmic Staircase Pulse Sweep, 2-58,
2-73, 3-53
Logarithmic Staircase Pulse Sweep
Parameters,
2-66
Logarithmic Staircase Sweep, 2-56, 2-70, 3-50
Logarithmic Staircase Sweep
Parameters, 2-64
Low Current, 3-83
M
Machine Status, 3-66
Measure Capabilities, 1-4
Measure Only, 1-4, 2-47
Measure Range Changed, 3-73
Measurement Overflow, 3-73
Measurement Parameters, 3-68
Measurement Range, 2-46
Measurement settling time, 3-83
Measurement Time, 3-86
Memory Test
2-41
Menu, 1-15, 2-36
Messages, 3-2
Model 7054 High Voltage Scanner Card, 2-32
Model
7058 Low Current Switching
Card,
2-21
Model 7070-PCA Prototype Circuit
Assembly, 2-32
Model 7072 Semiconductor Matrix
Card, 2-28
Model 7072-HV
High Voltage Semiconduc-
tor Matrix Card, 2-28
Model 7152 Low Current Matrix Card, 2-24
Model 7154 2-Pole
High Voltage Scanner
Card,
2-31
Model 8006 Component Test Fixture, 2-10
Model
Number and Firmware Revision, 3-62
Modify Sweep, 1-15, 2-78, 3-16
Multi Unit Connections, 2-16
Multiple Commands, 3-12
Multiple-Option Commands, 3-12
Must Create Sweep, 3-72
N
No Sweep Points, 3-72
No. Points,
2-61
Not in Remote, 3-4, 3-73
0
On and off Time, 2-61
Operate, 1-14,2-49,3-44
Operating Boundaries, 1-9
Operating Functions, 1-4
Optimizing Source
and Measurement
Speed, 3-83
Order of Command Execution, 3-13
Output, 1-16
Output Data Format, 3-28
Output LO, 1-16
Output Sense, 3-45
Output Triggers, 2-88, 3-59
p
Parameter Definitions, 2-61
Pending Trigger, 3-4
Performance Verification, 236/237,
F-1
Points/Decade, 2-62
Power, 1-14
Power Cord, 1-19, 2-4
Power Up, 1-19,
2-3
Power Up Configuration, 2-4
Power
Up Cycle, 1-19
Primary Address,
3-1
Pulse Sweep, 2-57, 2-71
Pulse Sweep Parameters, 2-65
Pulse Times Not Met, 3-72
R
Range, 2-62
Range Changes, 3-85
Range Changing, 3-83
Recall, 1-15, 2-92
Remote, 3-5
Remote Enable, 3-6
Remote Sense, 1-9, 3-45
Resolution, 3-58
Rotary Knob, 1-15
s
Select 1-15
Selective Device Clear, 3-7
Self Test 2-4
Self-tests, 3-36
Sense, 1-7,
2-9, 2-39
Sense HI, 1-16
Sense LO, 1-16
Serial Poll Byte Format, 3-40
Serial Polling, 3-7
Setup, 1-15
Shielding,
2-9
Software Rev, 2-4
Source, 2-44
Source
and Function, 3-27
Source Capabilities, 1-3
Source I Measure
V, 1-7,1-10
Source Measure, 1-14, 2-44
Source Only, 1-4
Source Range, 2-44
Source settling time, 3-83
Source V Measure
I, 1-7, 1-11
Source-Delay-Measure, 1-4,2-81
SRQ Mask, 3-40
Standby, 2-49, 3-44
Start
and Stop, 2-62
Status, 3-62
Step, 2-62
Stored Message, 3-66
Subordinate Sweep, 2-95
Suppress, 1-14, 2-52,3-81
Suppression Value, 3-69
Sweep,
2-91
Sweep Buffer, 1-6
Sweep Buffer Filled, 3-72
Sweep End
Output Trigger, 2-88
Sweep End"trigger, 3-59
Sweep Performance,
3-91
Sweep Times, 3-83
Sweep Waveforms, 1-6,2-55
Switching Configurations,
2-21
Synchronous Sweep, 2-95