Kikusui PAS 10-35 - Page 8

VI PAS SERIES
Chapter4 Remote Control
4.1 Analog Remote Control - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -4-1
4.1.1 About the J1 Connector - - - - - - - - - - - - - - - - - - - - - - - - - - - -4-2
4.1.2 Controlling the Output Voltage Using External Voltage - - - - - -4-5
4.1.3 Controlling the Output Voltage Using External Resistance- - - - -4-8
4.1.4 Controlling the output current using external voltage - - - - - - - 4-11
4.1.5 Controlling the Output Current Using External Resistance- - - - 4-14
4.1.6 Controlling the Output ON/OFF Using External Contact - - - - - 4-17
4.1.7 Controlling the Output Shutdown Using External Contact - - - - 4-19
4.2 Remote Monitoring - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-21
4.2.1 External Monitoring of the Output Voltage and Output Current 4-21
4.2.2 External Monitoring of the Operation Mode - - - - - - - - - - - - - 4-22
4.3 Digital Remote Control - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-23
4.3.1 Connecting of the Power Supply Controller and Device messages
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-23
Chapter5 Parallel and Series Operation
5.1 Master-Slave Series Operation - - - - - - - - - - - - - - - - - - - - - - - - - - -5-2
5.1.1 Functions during Master-Slave Series Operation - - - - - - - - - - -5-2
5.1.2 J1 Connector Connection (Series Operation) - - - - - - - - - - - - - -5-4
5.1.3 Load Connection for Series Operation - - - - - - - - - - - - - - - - - -5-5
5.1.4 Master-Slave Series Operation Setup - - - - - - - - - - - - - - - - - - -5-6
5.1.5 Master-Slave Series Operation Procedure - - - - - - - - - - - - - - - -5-7
5.2 Master-Slave Parallel Operation - - - - - - - - - - - - - - - - - - - - - - - - - -5-8
5.2.1 Functions during Master-Slave Parallel Operation - - - - - - - - - -5-8
5.2.2 J1 Connector Connection (Parallel Operation) - - - - - - - - - - - - 5-10
5.2.3 Load Connection for Parallel Operation - - - - - - - - - - - - - - - - 5-11
5.2.4 Master-Slave Parallel Operation Setup - - - - - - - - - - - - - - - - - 5-13
5.2.5 Master-slave parallel Operation Procedure - - - - - - - - - - - - - - 5-14
Chapter6 Names and Functions of Controls
6.1 Front Panel - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -6-1
6.2 Rear Panel - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -6-5
Chapter7 Maintenance
7.1 Cleaning - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -7-1
7.1.1 Cleaning the Panels - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -7-1
7.1.2 Cleaning the Dust Filter - - - - - - - - - - - - - - - - - - - - - - - - - - - -7-2
7.2 Inspection - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -7-8
7.3 Calibration- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -7-8
7.3.1 Test Equipment Required - - - - - - - - - - - - - - - - - - - - - - - - - - -7-8