Kohler CV11-16 - Page 12

1.10
Section 1
Safety and General Information
Cylinder Head
Cylinder Head Fastener Torque (torque in 2 increments)......... 20, 40.7 N·m (15, 30 ft. lb.)
Max. Out-of-Flatness ............................................................... 0.076 mm (0.003 in.)
Rocker Pedestal Fastener Torque ........................................... 11.3 N·m (100 in. lb.)
Electric Starter
Starter Thru Bolt Torque
UTE/Johnson Electric, Eaton (Inertia Drive) ...................... 4.5-5.7 N·m (40-50 in. lb.)
Nippendenso (Solenoid Shift)............................................ 4.5-7.5 N·m (40-84 in. lb.)
Delco-Remy (Solenoid Shift) ............................................. 5.6-9.0 N·m (49-79 in. lb.)
Starter Mounting Screw Torque (All) ........................................ 15.3 N·m (135 in. lb.)
Solenoid Mounting Hardware (Nut/Screw) Torque
Nippendenso Starter ......................................................... 6.0-9.0 N·m (53-79 in. lb.)
Delco-Remy Starter........................................................... 4.0-6.0 N·m (35-53 in. lb.)
Brush Holder Mounting Screw Torque
Delco-Remy Starter........................................................... 2.5-3.3 N·m (22-29 in. lb.)
Nut, Positive (+) Brush Lead Torque
Nippendenso Starter ................................................... 8.0-12.0 N·m (71-106 in. lb.)
Delco-Remy Starter .................................................... 6.0-9.0 N·m (53-79 in. lb.)
Fan/Flywheel
Fan Fastener Torque ............................................................... 9.9 N·m (88 in. lb.)
Flywheel Retaining Screw Torque ............................................ 66.4 N·m (49 ft. lb.)
Fuel Pump
Fuel Pump Fastener Torque .................................................... 9.0 N·m (80 in. lb.) Into new as-cast hole
4.2-5.1 N·m (37-45 in. lb.) Into used hole
Fuel Pump Pad Cover Fastener Torque .................................. 10.7 N·m (95 in. lb.) Into new as-cast hole
7.3 N·m (65 in. lb.) Into used hole
Governor
Governor Cross Shaft to Crankcase Running Clearance......... 0.025/0.075 mm (0.0010/0.0030 in.)
Governor Cross Shaft O.D.
New................................................................................... 5.975/6.000 mm (0.2352/0.2362 in.)
Max. Wear Limit ................................................................ 5.962 mm (0.2347 in.)
Governor Gear Shaft-to-Governor Gear Running Clearance ... 0.050/0.160 mm (0.0019/0.0063 in.)
Governor Gear Shaft O.D.
New................................................................................... 5.990/6.000 mm (0.2358/0.2362 in.)
Max. Wear Limit ................................................................ 5.977 mm (0.2353 in.)
Ignition
Spark Plug Type (Champion
®
or equivalent)............................. RC12YC (Standard) or
Premium Gold 2071 (Pro Series)
Spark Plug Gap
CV11-15, CV460-465, CV490-495 .................................... 1.02 mm (0.040 in.)
CV11-14 LP, CV16 ............................................................ 0.76 mm (0.030 in.)