Multitec
1. General
The Multitec pump has been developed in accordance with state-
of-the-art technology; it is manufactured with utmost care and
subject to continuous quality control.
These operating instructions are intended to facilitate operation
of the pump and help in commissioning and maintenance.
The manual contains important information for reliable, proper
and efficient operation.
These operating instructions do not take into account local
regulations; the operator must be ensure that such regulations
are strictly observed by all, including the personnel called in for
installation.
Multitec pumps must not be operated beyond the limit values
specified in the technical documentation for the medium handled,
capacity, speed, density, pressure, temperature and motor rating.
Make sure that operation is in accordance with the instructions
laid down in this manual or in the contract documentation.
The name plate indicates the type series / size and the main
operating data; please quote this information in all correspondence
and particularly when ordering spare parts.
If you need any additional information or instructions exceeding
the scope of this manual or in case of damage please contact
KSB’s after-sales service.
2. Safety
These operating instructions contain fundamental information
which must be complied with during installation, operation and
maintenance. Therefore this operating manual must be read and
understood both by the installing personel and the responsible
trained personnel / operators prior to installation and
commissioning, and it must always be kept close to the location
of operation of the machine / unit for easy access.
Not only must the general safety instructions laid down in this
chapter on “Safety” be complied with, but also the safety
instructions outlined under specific headings, plut :
- the general safety rules for working materials and protective
devices;
- the applicable organisational guidelines for the commissioning
of working materials and tools (work guidelines R233-1 to
R233-10 and decree no. 93-41 dd. 11.01.93).
2.1 Marking of Instructions in the Manual
The safety instructions contained in this manual whose non-
observance might cause hazards to persons are specially
marked with the general hazard sign, namely :
(safety sign in accordance with ISO 7000-0434).
the electrical danger warning sign is
(safety sign in accordance with IEC 417-5036).
The word
is used to introduce safety instructions whose nonobservance
may lead to damage to the machine and its functions.
Instructions attached directly to the machine, e.g.
- arrow indicating the direction of rotation
- markings for auxiliary connections
must always be complied with and be kept in perfectly legible
condition at all times. Noncompliance with these safety
instructions will lead to forfeiture of manufacturer’s warranties.
2.2 Personnel Qualification and Training
All personnel involved in the operation, maintenance, inspection
and installation of the machine must be fully qualified to carry out
the work involved.
Personnel responsibilities, competence and supervision must
be clearly defined by the operator. If the personnel in question is
not already in possession of the requisite know-how, appropriate
training and instruction must be provided. If required, the operator
may commission the manufacturer / supplier to take care of such
training. In addition, the operator is responsible for ensuring that
the contents of the operating instructions are fully understood by
the responsible personnel.
2.3 Non-Compliance with Safety Instructions
Non-compliance with safety instructions can jeopardise the safety
of personnel, the environment and the machine itself. Non-
compliance with these safety instructions will also lead to forfeiture
of any and all rights to claims for damages.
In particular, non-compliance can, for example result in :
- failure of important machine / unit functions
- failure of prescribed maintenance and servicing practices
- hazard to persons by electrical, mechanical thermal and
chemical effects
- hazard to the environment due to leakage of hazardous
substances.
2.4 Safety Awareness
It is imperative to comply with the safety instructions contained
in this manual, the relevant national health and safety regulations
and the operator’s own internal work, operation and safety
regulations.
2.5 Safety Instructions for the Operator / User
- Any hot or cold components that could pose a hazard must
be equipped with a guard by the operator.
- Guards which are fitted to prevent accidental contact with
moving parts (e.g. coupling) must not be removed whilst the
machine is operating.
- Leakages (e.g. at the shaft seal) of hazardous media handled
(e.g. explosive, toxic, hot) must be contained so as to avoid
any danger to persons and the environment. Pertinent legal
provisions must be adhered to.
- Electrical hazards must be eliminated. (In this respect refer
to the relevant safety regulations applicable to different
countries and/or the local energy supply companies.)
1
To Next Page
Loading...
