Multi Edit Mode
Controls Page
5-33
Controller
Number
Controller
Destination
Description
146 TransDown Transpose Down (ST)
147 Arp On/Off Values 0-63 turn the Arpeggiator Off, Values 64-127 turn the Arpeggiator On
148 CC Seq On/Off Values 0-63 turn the CC Sequencer Off, Values 64-127 turn the CC Sequencer On.
149 Mute Zone
Mute Zone – Values above 64 will mute the zone that sends values to this
destination, values below or equal to 64 will unmute the zone.
150 ArpOrder
Arpeggiator PlayOrder, each range of values selects one of nine settings in order of
the parameter list: 0-14, 15-28, 29-42, 43-56, 57-70,71-84, 85-98, 99-112, 113-127.
(See Play Order on page 3-20)
151 ArpBeats
Values from 0-127 change the Arpeggiator Beats value (see Beats on page 3-17 for
details).
152 ArpShift
The 88 Arpeggiator Shift steps are scaled over the 128 MIDI controller values, so
that 0 = 0 steps and 127 = 88 steps. (See Shift Amount on page 3-18 for details).
153 ArpLimit
The 60 Arpeggiator Shift Limit steps are scaled over the 128 MIDI controller values,
so that 0 = 0 steps and 127 = 60 steps. (See Shift Limit on page 3-18)
154 ArpLmtOp
Arpeggiator Shift Limit Option, each range of values selects one of seven options in
order of parameters list: 0-18, 19-36, 37-54, 55-72, 73-90, 91-108, 109-127. (See
Limit Option on page 3-16)
155 ArpVel
Arpeggiator Velocity Mode, each range of values selects one of twenty-three op-
tions in order of parameters list: 0-5, 6-10, 11-15...101-105, 106-110, 111-127. (See
Velocity on page 3-20).
156 Arp Dur
The Arpeggiator Duration % values are scaled over the 128 MIDI controller values,
so that 0 = 1% and 127 = 100%. (See Duration on page 3-24)
157 Latch Sustain
To control the Arpeggiator Latch switch, 0-63 = off, 64-127 = on. (See Latch on page
3-14)
158 Latch2:Sost To control the Arpeggiator Latch2 switch, 0-63 = off, 64-127 = on.
160 SusLatch For Arpeggiator Latch Pedals mode, 0-63 = off, 64-127 = on.
161 Panic
Sends an “all notes off” message and an “reset all controllers” message on all 16
MIDI channels.
162 SoloZn
Solo Zone - Values above 64 will solo the zone that sends values to this destination,
values below or equal to 64 will unsolo the zone. When soloing a Zone, all other
Zones will become muted, and unmuting a muted Zone will make that Zone the
soloed zone. If the currently soloed Zone has a controller assigned to Destination
149 (Mute Zone), solo mode can be canceled by sending a value to this destination.
163 Riff OnOff
If Riff is set to On on the Riff page, values 64-127 will trigger the riff, values 0-63 will
release the riff.
165 Riff Duration
Controls the Riff Duration parameter. The Duration value is calculated by multiplying
the received controller value by 1000, and dividing the answer by 128 (any decimal
points are taken off the nal value.) Here are some example values: 7 = 54%, 13 =
101%,19 = 148%, 32 = 250%, 64 = 500%, 127 = 992%
166 Riff Velocity
Controls the Riff Velocity parameter. The Velocity value is calculated by multiply-
ing the received controller value by 2. For Example, 25 = 50%, 50 = 100%, 100 =
200%, 127 = 254%.
167 Riff Delay
Controls the Riff Offset parameter. Controller value 64 = 0 offset ticks. Each value
away from 64 = 512 offset ticks. For example, 63 = -512 offset ticks, 65 = +512
offset ticks, 0 = -32768 offset ticks, 127 = +32256 offset ticks.
168 TapTempo
Assign this to a switch (set to Type: Toggled) to control the tap tempo function, then
tap the switch in time to set the Multi tempo.
170 -ArpShift
Sets Arpeggiator values for Shift to negative. 0-63 = off, 64-127 = on. (See Shift
Amount on page 3-18)
171 ShiftPatt
Selects one of the 128 patterns in the current Arpeggiator Shift Pattern Bank. (See
Shift Pattern on page 3-18)
172 ShiftPBank
A controller value selects the corresponding Shift Pattern Bank for the Arpeggiator
page of a controller’s zone. For example, controller value 2 selects Shift Pattern
bank 2, controller value 7 selects Shift Pattern bank 7.
To Next Page
Loading...
