Laversab 6300 - APPENDIX E: WI-FI OPERATION

6300 Rev H User’s Manual
125-9106A
APPENDIX
This section includes the process for setting
for use with the 6300. The wireless Remote will function only if the 6300 has been installed with the optional
wireless capability.
The wireless antenna is located on the Top Panel of the
taken not to obstruct or cover the antenna with metallic objects, since this will be detrimental to effective Wi
Fi operation.
Note: The Wired-
Remote must be connected to the tester and operational even when the
used.
E.1 iPad COMPATIBILITY
The Laversab
App is compatible with the following iPads configured with iOS 8.1 or higher:
iPad 2, iPad Mini, iPad Mini 2
, iPad Mini 3, iPad Mini 4, iPad Air, iPad Air 2, iPad Pro.
E.2
DOWNLOADING THE APP
The Laversab App must be downloaded from the Apple App Store. Although the App itself is provided at
no charge, a credit card is required t
download the App.
Once you have access to the App Store, search for “Laversab” and the app should appear
shown below. If more than one App is displayed, select the App labeled “CH
version number. If more than one version of the App is displayed, select the one with the latest version
number. Do not select the App labeled “CH
tester.
E.3 NETWORK SELECTION
Once the App has been installed on your iPad, the following steps need to be performed to c
tester through the App.
a.
Turn ON the tester and ensure that the Wired
internal wireless access-
poi
b.
On the iPad select the ‘Settings’ icon. Then select the Wi
right side will show all the Wi
xxxxx”, where ‘xxxxx’ is the seria
c.
Select the network with the correct label, ensuring that the serial number matches the serial
number of your tester. The serial number of the tester can be found on the label placed on the
inside of the lid
of the tester’s case, towards the bottom right corner.
d.
Once the correct network has been selected, you may be asked for a password for this network.
The password is “lavus505” (the first letter is a non
entered, the Settings
column
APPENDIX
E : WI-FI OPERATION
This section includes the process for setting
up a wireless Remote, such as an iPad,
with the appropriate App
for use with the 6300. The wireless Remote will function only if the 6300 has been installed with the optional
The wireless antenna is located on the Top Panel of the
tester, as shown in Figure 2.1 on Page 9. Care must be
taken not to obstruct or cover the antenna with metallic objects, since this will be detrimental to effective Wi
Remote must be connected to the tester and operational even when the
App is compatible with the following iPads configured with iOS 8.1 or higher:
, iPad Mini 3, iPad Mini 4, iPad Air, iPad Air 2, iPad Pro.
DOWNLOADING THE APP
The Laversab App must be downloaded from the Apple App Store. Although the App itself is provided at
no charge, a credit card is required t
o create an Apple Store accou
nt which enables you to access and
Once you have access to the App Store, search for “Laversab” and the app should appear
shown below. If more than one App is displayed, select the App labeled “CH
-
2 / vx.xx”, where ‘
version number. If more than one version of the App is displayed, select the one with the latest version
number. Do not select the App labeled “CH
-3 / vx.xx”, since this is intended for use
only
Once the App has been installed on your iPad, the following steps need to be performed to c
Turn ON the tester and ensure that the Wired
-
Remote is displaying the Main Screen. The
poi
nt will now be active.
On the iPad select the ‘Settings’ icon. Then select the Wi
-Fi section.
(See Figure E.1 below).
right side will show all the Wi
-
Fi networks available. One of the networks will be labeled “LAV
xxxxx”, where ‘xxxxx’ is the seria
l number
of the tester you want to connect to.
Select the network with the correct label, ensuring that the serial number matches the serial
number of your tester. The serial number of the tester can be found on the label placed on the
of the tester’s case, towards the bottom right corner.
Once the correct network has been selected, you may be asked for a password for this network.
The password is “lavus505” (the first letter is a non
-
capitalized L). Once the password has been
column
will show the selected network (LAV-xxxxx)
in the Wi
Page 84
with the appropriate App
for use with the 6300. The wireless Remote will function only if the 6300 has been installed with the optional
tester, as shown in Figure 2.1 on Page 9. Care must be
taken not to obstruct or cover the antenna with metallic objects, since this will be detrimental to effective Wi
-
Remote must be connected to the tester and operational even when the
iPad is being
App is compatible with the following iPads configured with iOS 8.1 or higher:
The Laversab App must be downloaded from the Apple App Store. Although the App itself is provided at
nt which enables you to access and
Once you have access to the App Store, search for “Laversab” and the app should appear
with the icon as
2 / vx.xx”, where ‘
x.xx’ is the
version number. If more than one version of the App is displayed, select the one with the latest version
only
with a 3-Output
Once the App has been installed on your iPad, the following steps need to be performed to c
onnect to the
Remote is displaying the Main Screen. The
(See Figure E.1 below).
The
Fi networks available. One of the networks will be labeled “LAV
-
of the tester you want to connect to.
Select the network with the correct label, ensuring that the serial number matches the serial
number of your tester. The serial number of the tester can be found on the label placed on the
Once the correct network has been selected, you may be asked for a password for this network.
capitalized L). Once the password has been
in the Wi
-Fi section.