Magnetek Elevator Quattro DC - Page 10

Quattro DC Quick Parameter Reference
8
Sub
menu
Parameter Units Range Default
Site
Setting
A2 DECEL JERK OUT 3
ft/s
3
0.0 – 29.9 8.0
m/s
3
0.00 – 9.99 2.40
A2
ACCEL RATE 4
ft/s
3
0.0 – 7.99 5
m/s
3
0.000 – 3.999 1.52
A2
DECEL RATE 4
ft/s
3
0.0 – 7.99 5
m/s
3
0.000 – 3.999 1.52
A2 ACCEL JERK IN 4
ft/s
3
0.0 – 29.9 0
m/s
3
0.00 – 9.99 0
A2 ACCEL JERK OUT 4
ft/s
3
0.0 – 29.9 0
m/s
3
0.00 – 9.99 0
A2 DECEL JERK IN 4
ft/s
3
0.0 – 29.9 0
m/s
3
0.00 – 9.99 0
A2 DECEL JERK OUT 4
ft/s
3
0.0 – 29.9 0
m/s
3
0.00 – 9.99 0
A3 Multistep Ref A3 Submenu – See Multistep Ref A3 submenu on page 53.
A3 SPEED COMMAND 1
ft/min
-3000.0 – +3000.0 0.0
m/sec
-16.000 – +16.000 0.000
A3 SPEED COMMAND 2
ft/min
-3000.0 – +3000.0 0.0
m/sec
-16.000 – +16.000 0.000
A3 SPEED COMMAND 3
ft/min
-3000.0 – +3000.0 0.0
m/sec
-16.000 – +16.000 0.000
A3 SPEED COMMAND 4
ft/min
-3000.0 – +3000.0 0.0
m/sec
-16.000 – +16.000 0.000
A3 SPEED COMMAND 5
ft/min
-3000.0 – +3000.0 0.0
m/sec
-16.000 – +16.000 0.000
A3 SPEED COMMAND 6
ft/min
-3000.0 – +3000.0 0.0
m/sec
-16.000 – +16.000 0.000
A3 SPEED COMMAND 7
ft/min
-3000.0 – +3000.0 0.0
m/sec
-16.000 – +16.000 0.000
A3 SPEED COMMAND 8
ft/min
-3000.0 – +3000.0 0.0
m/sec
-16.000 – +16.000 0.000
A3 SPEED COMMAND 9
ft/min
-3000.0 – +3000.0 0.0
m/sec
-16.000 – +16.000 0.000
A3 SPEED COMMAND 10
ft/min
-3000.0 – +3000.0 0.0
m/sec
-16.000 – +16.000 0.000
A3 SPEED COMMAND 11
ft/min
-3000.0 – +3000.0 0.0
m/sec
-16.000 – +16.000 0.000
A3 SPEED COMMAND 12
ft/min
-3000.0 – +3000.0 0.0
m/sec
-16.000 – +16.000 0.000
A3 SPEED COMMAND 13
ft/min
-3000.0 – +3000.0 0.0
m/sec
-16.000 – +16.000 0.000
A3 ft/min
-3000.0 – +3000.0 0.0