What does it mean if the mammotome REVOLVE Medical Equipment system reports: “Incompatible Probe – Replace Probe” during function execution with Error Code 451?
If the mammotome Medical Equipment system reports: “Incompatible Probe – Replace Probe” during function execution with Error Code 451, it means an incorrect type of probe is attached. Remove the probe attached to the holster and replace it with a new probe.
What should I do if the mammotome REVOLVE probe attachment is difficult?
If you're finding it difficult to attach the probe to the holster on your mammotome Medical Equipment, it might be because the probe is being loaded onto the holster at an angle. To resolve this, keep the probe parallel to the holster (along the long axis) when attaching it.
What to do if the mammotome Medical Equipment cutter remains stuck in the open aperture position?
If the cutter remains stuck in the open aperture position on your mammotome Medical Equipment, a homing error may have occurred. Remove the probe from the holster, rotate the cutter gear on the bottom of the probe until the aperture is only 1/3 open, then reattach the probe to the holster and reinitialize the system.
Why is there irregular gear noise during initialization of my mammotome Medical Equipment?
Irregular gear noise during initialization of the mammotome Medical Equipment could be due to the probe not being correctly attached to the holster. Remove the probe and reattach it to the holster. If the noise occurs again, remove the probe and inspect the cutter gear on the probe. If it is not damaged, replace the probe on the holster and proceed through initialization. If the cutter gear is damaged, discard the damaged probe and continue with a new probe.
What does it mean if the mammotome REVOLVE system reports: “Probe Error – Replace Probe” during function execution with Error Codes 450, 452, 454, 455, 456?
If the mammotome Medical Equipment system reports: “Probe Error – Replace Probe” during function execution with Error Codes 450, 452, 454, 455, 456, it means the system is unable to connect or communicate with the probe with the holster or that the biopsy count has been exceeded. Remove the probe attached to the holster and replace it with a new probe.
What to do if my mammotome Medical Equipment SMS collection chambers are not at the anticipated location after initialization?
If the Specimen Management System (SMS) collection chambers are not at the anticipated location after initialization of your mammotome Medical Equipment, it could be due to: * Probe/holster did not initialize correctly: Remove the probe and manually rotate the specimen collection chambers to align with the alignment indicator on the probe, being careful not to pinch or dislodge the chambers. Replace the probe on the holster and proceed through initializations. If Chamber 7 is desired for the next sample, select Advance to Chamber 7 on the touchscreen interface. * SMS cup was misaligned prior to attaching the probe to the holster: Remove the probe from the holster. Manually rotate the SMS cup chambers (not the outer cup) to align the 13th chamber with the sample port (marked by an ‘M’ ...
What should I do if the mammotome Medical Equipment system reports holster is not compatible: Error Code 203?
If the mammotome Medical Equipment system reports that the holster is not compatible and shows Error Code 203, it means that the control module and the holster have incompatible software versions. Use a holster that is compatible with the control module’s current software version.
What to do if the mammotome Medical Equipment system returns to Standby and reports error message: “Vacuum Error, Check Tubing Connections” Error Code 400 or 402?
If the mammotome Medical Equipment system returns to Standby and reports error message: “Vacuum Error, Check Tubing Connections” Error Code 400 or 402, it could be due to a vacuum canister leak, or the vacuum pump is not working properly. Ensure the vacuum tubing is connected. Check that all vacuum canister lid ports are sealed and repeat system initialization.
What to do if I cannot insert the valve cartridge into the control module’s vacuum connection slot in mammotome REVOLVE Medical Equipment?
If you cannot insert the valve cartridge into the control module’s vacuum connection slot in your mammotome Medical Equipment, it is likely due to misalignment of the valve slots. Manually align the valve cartridge T-slots with the orientation of the control module valve actuators. Alternatively, proceed through initialization without the valve cartridge attached to reset the valve alignment, and then reattach the valve cartridge to the control module.
What to do if fluid does not visibly move in the vacuum tubing when the Vacuum button is pressed and released on my mammotome REVOLVE Medical Equipment?
If fluid isn't visibly moving in the vacuum tubing when you press and release the Vacuum button on your mammotome Medical Equipment, it could be that the vacuum button is being held too long to trigger Clear/Dry Tap, but not long enough to trigger the Vacuum function. Adjust the length of time the user is pressing the button: faster for Clear/Dry Tap, longer for Vacuum.
Highlights critical safety information, potential hazards, and warnings for safe operation.
Provides general usage precautions and specific safety guidelines related to the system's electrical and operational aspects.
Describes the different types of probes (ST, U/S, EX) and their corresponding holsters.
Step-by-step instructions for unpacking system components and assembling them for initial use.
Guides through powering on the system, connecting components, and initial setup processes.
Detailed instructions on how to prepare the system and perform tissue sampling using EX mode.
Explains the biopsy cycle, sample acquisition, and handling of collected tissue specimens.
Detailed instructions for cleaning the main system components using specified detergents.
Procedures for cleaning and disinfecting ST, U/S, and EX holsters using different options.
Overview of the graphic user interface, touchscreens, and button functionalities on the control module.
Provides solutions for common problems related to system components like holsters and probes.
Addresses issues related to system software, error messages, and incompatible components.
General| Brand | mammotome |
|---|---|
| Model | REVOLVE |
| Category | Medical Equipment |
| Language | English |
To Next Page