McConnel SR460 - Page 22

To Next Page

To Previous Page

Figure 1.11 Working Dimensions

NOTE: These illustrations for working and transport dimensions are illustrated by a SR460 for visual purposes

only.

Figure 1.12 Transport dimensions

Main Page

Table of Contents10
Machine Description14
Intended Usage14
Allowed Uses14
Improper Uses14
General Arrangement15
Sr46016
Sr62017
Sr82018
Machine Identification19
Rotation Definitions & Conventions20
Machine Specification21
Standard Specification21
Machine Options23
Safety25
Level of Danger25
Terminology25
Safe Use26
Operators Manual26
Personnel Preparation26
Tractor and Machine Preparation for Work26
Work Site Preparation29
Machine at Work & Observation30
Transporting the Machine32
Machine Storage33
Safe Maintenance34
Safety & Operational Decals37
Definitions37
Placement39
Replacement40
Guards40
Mandatory Guards40
Sound41
Personal Protective Equipment41
The Machine & the Environment41
Disposal42
Proposition 6543
Machine Preparation44
Lifting the Machine44
Post-Delivery/First Use Inspection45
Tractor Inspection45
Machine Adjustment45
PTO Shaft46
PTO Setup & Adjustment (First Use)46
Bottoming out Test46
Engagement Test47
Modifying & Shortening the Input PTO Shaft47
Fitting the PTO Shaft49
Wheels & Tyre Installation49
Usage Instruction50
Operator Requirements50
Tractor Requirements51
Connecting & Disconnecting Hydraulic Hoses & Electric Cables51
Hitching & Unhitching the Machine53
Adjustable Pick-Up Hitch53
Fixed Pick-Up Hitch53
Safety Towing Chain56
PTO Shaft57
Fitting & Removal of the Input PTO Shaft57
PTO Shaft Specifications59
Unfolding & Folding the Machine60
Setting up the Machine61
Front to Rear62
Wings63
Setting Cutting Height67
Sr460/62067
Sr82069
Work Site Assessment70
Foreign Debris Hazards70
Stopping the Machine in an Emergency71
Bystanders71
Weather72
Fire72
Safe Driving Practices72
Using the Machine74
Engaging the Power Take-Off (PTO)74
Disengaging the Power Take-Off (PTO)74
Forward & Power Take-Off Speed75
Cornering75
Crossing Ditches & Steep Inclines76
Un-Level Ground77
Road Transporting the Machine77
Transport Width Adjustment (SR460 Only)78
Marker Boards (SR460 Only)78
Transporting the Machine on a Trailer79
Maintenance80
Periodic Maintenance80
Lubrication & Greasing80
Gearboxes80
PTO Shaft83
General Machine Greasing Point Locations86
Greasing Schedule87
PTO Shaft87
Size Adjustment & Fitting to the Tractor87
Greasing87
Input PTO Shaft - Bearing Ring Replacement88
Wing PTO Shaft - Bearing Ring Replacement92
Slip Clutch94
Slip Clutch Disassembly & Servicing94
Freeing Seized Clutch Plates97
Clutch Settings98
Blades & Anti-Scalp Dishes99
Blade Options99
Blade Inspection99
Blade Sharpening & Straightening101
Blade Removal & Replacement101
Blade Bolt Inspection102
Anti-Scalp Dish Inspection103
Anti-Scalp Dish, Blade & Blade Carrier Removal & Replacement104
Hydraulic Components107
Ram Inspection108
Wing Ram Replacement108
Centre Axle Lift Ram Replacement111
Hoses113
Machine Hose Diagrams114
Wheels, Hubs & Tyres116
Tyre Pressures117
Hub Greasing117
Maximum Road Operating Speed117
Other Key Components118
Pins & Bushes118
Skids118
Torque Settings119
Nuts & Bolts119
Hydraulic Fittings120
Machine Inspection Record121
Machine Storage123
Preparing the Machine for Storage123
Returning the Machine Back to Work124
Troubleshooting125

McConnel SR460 - Page 22

Table of Contents

Related product manuals