MCCOY KT5500 - Rigging and Overhead Lifting; Maintenance Safety; Replacement Parts; Environment Impact

©2008-2017 McCoy Global
Manual № TM12012
80-0420-23 POWER TONG
Section 1
Page 1.8
Introduction
!
DANGER
NEVER STAND BENEATH A SUSPENDED LOAD
!
DANGER
ALWAYS MEASURE ELECTRICAL CIRCUITS TO CONFIRM DEACTIVATION BEFORE PROCEEDING WITH
MAINTENANCE
1.2.5 Replacement Parts
All consumable and replacement parts must meet or exceed OEM specifications in order to maintain equipment
integrity. Do not replace protective equipment such as hydraulic switches, circuit breakers, and fuses without first
consulting with McCoy Global. Do not replace electrical or control hardware without consulting with McCoy Global.
Using non-OEM replacement parts without the approval of McCoy Global may void equipment warranty.
1.2.6 Environmental Impact
McCoy Global equipment uses materials that may be harmful to the environment if improperly disposed of
(hydraulic fluid, grease, fuel, electrical components, etc.). Dispose of all materials according to established
environmental protection regulations in conjunction with published federal, state, provincial, and civic legislation.
In all cases observance of the following is the full responsibility of the user:
• all descriptions, information and instructions set out in this manual
• any regulation or requirement issued by an authority or agency which may influence operation, safety
or integrity of the equipment that overrules the content of this document.
• any legal or other mandatory regulation in force governing accident prevention or environmental
protection.
1.2.3 Rigging and Overhead Lifting
McCoy Global recommends following an industry-accepted standard such as OSHA, ASME B30.9-2006, or
manufacturer’s guidelines when performing any rigging and overhead lifting. Use by untrained persons is
hazardous. Improper use will result in serious injury or death. Do not exceed rated capacity. Slings will fail if
damaged, abused, misused, overused, or improperly maintained. Never stand beneath a suspended load.
1.2.4 Maintenance Safety
All personnel are responsible for performing maintenance tasks in a manner that ensures worker, equipment, and
environmental safety, and may require taking additional steps that are not identified in this section.
Maintenance of equipment shall be performed only by designated qualified maintenance personnel. Do not begin
a maintenance task without the proper tools or materials on hand, or the proper drawings and documentation
necessary.
Isolate the location of the maintenance under way to prevent unaware personnel from inadvertently exposing
themselves to a hazard. Use tape, rope, or signage to clearly indicate “off-limits” area.
Where applicable ensure electrical circuits within the affected equipment are deactivated or de-energized by an
authorized, qualified person and locked out if necessary. Do not disconnect a live electrical circuit unless location
is known to be non-hazardous.
!
WARNING
WHEN REPAINTING EQUIPMENT, THE PAINT COAT BEING APPLIED SHOULD NEVER EXCEED 2MM
IN THICKNESS. EXCEEDING THIS THICKNESS MAY FACILITATE STATIC CHARGE BUILDUP AND
PRESENT A POSSIBLE SPARK RISK ASSOCIATED WITH STATIC DISCHARGE.
1.3 ACRONYMS AND TERMINOLOGY
1.3.1 Acronyms and Definitions
ACRONYM DEFINITION
ANSI American National Standards Institute
API American Petroleum Institute
ASME American Society of Mechanical Engineers
ATEX Appareils destinés à être utilisés en ATmosphères EXplosibles
BDC Bottom dead centre
CBU CLINCHER
®
-style backup
CE Conformité Européenne
CCW Counter-clockwise
COG Centre of gravity
CW Clockwise
DS Driller’s side
EU European Union
HMI Human-machine interface
HPU Hydraulic power unit
HSE Health, Safety, and Environmental (context: protection)
ID Inside diameter
ISO International Organization for Standardization
JDK Jaw die kit
JSA Job safety assessment
LH Left-hand
LJBU LOCKJAW™ backup
MBU “McCoy style” backup
N/A Not applicable or Not available (context-dependant)
NLGI National Lubricating Grease Institute
ODS Off-driller’s side
OEM Original equipment manufacturer
OSHA Occupational Safety and Health Administration
OD Outside diameter
PLC Programmable Logic Controller
PPE Personal Protective Equipment
PSI Pounds per square inch (pressure)
RH Right-hand
VAC Volts, alternating current
VDC Volts, direct current
WLL Working Load Limit