Why won't my METER Measuring Instruments SC-1 calibrate, even after multiple attempts?
If your METER Measuring Instruments SC-1 will not calibrate, even after multiple attempts, it may not be in thermal equilibrium. Leave the sensor head at ambient conditions for 15 min and try again.
How to fix a METER Measuring Instruments SC-1 that does not turn on?
If your METER Measuring Instruments SC-1 does not turn on, check that the batteries are inserted correctly. If it still does not turn on, replace the batteries.
How to improve the visibility of the display on METER SC-1?
To improve the visibility of the display on your METER Measuring Instruments, you can adjust the contrast. Navigate to the Configuration tab, scroll down to Contrast, and use the UP and DOWN buttons to adjust the screen contrast level.
What to do if I get a Sensor Head Failure error on my METER SC-1?
If you encounter a Sensor Head Failure error on your METER Measuring Instruments, first verify the sensor head is securely connected to the serial port receptacle. If the error persists, restart the reading. You may also navigate to the Configuration tab, select Diagnostics, and press ENTER to save a Scan record. Contact Customer Support with the Scan record results ready for review.
Why am I getting a 'Firmware is corrupted!' error on my METER SC-1, and how do I fix it?
A 'Firmware is corrupted!' error on your METER Measuring Instruments may occur if the firmware was not loaded properly or an update is needed. Before reloading the new firmware, download any data. Check metergroup.com/sc1-support for a new firmware version.
What should I do if the conductance readings on my METER SC-1 are not as expected?
If the conductance readings on your METER Measuring Instruments are not what you expected, verify porometer accuracy. You can also recalibrate the sensor head, and clean the sensor head. If the Tefol n filter is wet or dirty, replace the filter.
Why does an infinity symbol appear instead of a measurement on my METER SC-1 Measuring Instruments?
An infinity symbol appears in place of the measurement because the stomatal conductance measurement is greater than or equal to 6,000 mmol/(m2s). Remove water from the leaf and repeat the measurement.
Why does the equilibration shake down period between measurements extend past 75 seconds on my METER Measuring Instruments?
If the equilibration shake down period between measurements extends past 75 s on your METER Measuring Instruments, check the integrity of the round rubber seal that caps the measurement chamber, as an air leak may have developed. Test for leaks by placing fresh desiccant in the desiccant chamber and leaving the sensor head undisturbed for 2-3 days. Use the diagnostics screen to check the RH of the unopened sensor head. If the RH is >10%, there is a leak.
What causes 'Too much drift' error in METER SC-1 and how to solve it?
If you are getting a 'Too much drift' error on your METER Measuring Instruments, it means that stable calibration readings were not achieved in 10 readings. Leave the sensor head at ambient conditions for 15 min and try again.
How to resolve a persistent high RH reading error on METER SC-1?
To resolve a persistent high RH reading error on your METER Measuring Instruments, check the desiccant and replace it if needed. The Tefol n filter may also be clogged, so replace the filter.
Steps to configure the SC-1 system date, time, and units for accurate readings.
Guide on how to take measurements using the SC-1 Leaf Porometer.
Factors affecting stomatal conductance readings like light, temperature, and humidity.
Step-by-step process for taking measurements with the SC-1 Leaf Porometer.
Instructions on how to save, annotate, or discard measurement data.
Steps to view previously saved test results on the SC-1 controller.
How to download measurement data from the SC-1 to a computer.
Procedures for erasing all stored data from the SC-1 controller or utility.
Detailed measurement and physical specifications for the SC-1 Leaf Porometer.
Description of the SC-1 sensor head, its function, and components.
Description of the SC-1 controller, its buttons, and interface.
Explanation of the main menus: Measurement, Data, and Configuration tabs.
Explanation of Auto and Manual measurement modes for the SC-1.
Details on the Leaf Porometer Utility software for data management and settings.
Explanation of the scientific principles behind SC-1 stomatal conductance measurements.
Guidance on ensuring and performing accurate stomatal conductance measurements.
Steps to verify the SC-1's accuracy before taking measurements.
Detailed steps for performing a user-initiated calibration of the SC-1.
Guidelines for system inspection, parts replacement, and instrument cleaning.
Instructions on how to change the AA batteries in the SC-1 controller.
Procedures for cleaning the SC-1 sensor head to maintain performance.
Steps for replacing damaged or missing leaf pads on the SC-1 sensor head.
Common problems, their causes, and solutions for the SC-1 Leaf Porometer.
Contact information for METER customer support in North America and Europe.
Agreement to METER Group's terms and conditions for using the instrument.
General| Brand | METER |
|---|---|
| Model | SC-1 |
| Category | Measuring Instruments |
| Language | English |
To Next Page
