Mitsubishi Electric NZ2EX2B-60AD4 - Page 176

174
017H Moderate error
External signal
assignment setting
error
The addresses set in the external signal
assignment function are different from those
assigned to the extension I/O module.
 indicates a type of the following errors:
0: Trigger conversion function
1: Input signal error detection function
2: Alert output function
3: Error output
4: Warning output
Adjust the external signal assignment function to
fall within the addresses assigned to the extension
I/O module.
0180H Moderate error
Same address for
the external signal
assignment function
The same address has been set in multiple
extension output modules for the external
signal assignment function.
Set a unique address.
020H
*1
Moderate error
Averaging time
setting out-of-range
The averaging time value set in CH Time
average/Count average/Moving average
(address: 0105H to 0108H) is outside the
range of 2 to 5000ms.
 indicates the number of the channel where
an error has occurred.
Set the averaging time to a value in the range of 2
to 5000ms.
The time average value set in CH Time
average/Count average/Moving average
(address: 0105H to 0108H) is less than "4 ×
Sampling period" (ms).
 indicates the number of the channel where
an error has occurred.
Adjust the time average value to be equal to or
greater than "4 × Sampling period" (ms).
030H
*1
Moderate error
Count average
setting out-of-range
The averaging count value set in CH Time
average/Count average/Moving average
(address: 0105H to 0108H) is outside the
range of 4 to 65000.
 indicates the number of the channel where
an error has occurred.
Set the averaging count to a value in the range of
4 to 65000.
031H
*1
Moderate error
Moving average
setting out-of-range
The moving average count value set in CH
Time average/Count average/Moving average
(address: 0105H to 0108H) is outside the
range of 2 to 128.
 indicates the number of the channel where
an error has occurred.
Set the moving average count to a value in the
range of 2 to 128.
0360H
*1
Moderate error
Conversion speed
setting out-of-range
The value set in Conversion speed setting
(address: 0001H) is other than 0 and 2.
Set one of the following values in Conversion
speed setting (address: 0001H).
• 400μs/channel (0H)
• 1ms/channel (1H)
• 100μs/channel (2H)
040H
*1
Moderate error
Offset/gain setting
value inverted
The user range setting value has been set to a
value where the offset value is equal to or
greater than the gain value.
 indicates the number of the channel where
an error has occurred.
Correct the setting so that the offset value is
smaller than the gain value.
06H
*1
Moderate error
Process alarm
setting error
The settings in CH1 Process alarm lower lower
limit value (address: 010FH) to CH4 Process
alarm upper upper limit value (address:
011EH) are invalid.
 indicates the number of the channel that has
been incorrectly set.
 indicates that the set values are in one of
the following conditions:
2: Process alarm lower lower limit value >
Process alarm lower upper limit value
3: Process alarm lower upper limit value >
Process alarm upper lower limit value
4: Process alarm upper lower limit value >
Process alarm upper upper limit value
Correct the settings in CH1 Process alarm lower
lower limit value (address: 010FH) to CH4
Process alarm upper upper limit value (address:
011EH).
0730H Moderate error
Mode switch setting
error
A value out of the range is set in mode switch
(address: 0000H).
Reset the mode switch (address: 0000H) to either
of the followings.
• Normal Mode (0H)
• Trigger conversion mode (1H)
• Automatical judgment mode (9H)
Error code
(hexadecimal)
Classification Error name Description and cause Action