MOJIX STAR3000 - Product Overview

To Next Page

To Previous Page

STAR™ 3000 / eNode3000 User Manual

Mojix Incorporated

Page

www.mojix.com

(877) 886-6549

External Component Interfaces:

1 eNode, 8 sensors, 8 actuators

Table 7: GPIO Operating Specification

8.1 Product Overview

The Terminal block is used to connect wires to and from the external sensor/actuator devices.

The Jumper block allows the circuits to be configured.

Figure 17: GPIO Unit Terminal Blocks

Each configuration group, made up of one terminal block and one jumper block, allow the

configuration of the two sensor circuits and two actuator circuits as required.

Main Page

Table of Contents7
Welcome to the Star System13
How this Guide Is Organized13
Overview13
Intended Audience13
Terminology14
Table 1: List of Star 3000 System Terms15
Star 3000 System Overview17
System Components17
Mojix Enodes: Distributed Transmitters17
STAR Receiver: Centralized Read and Control Point17
Master Controller17
Figure 1: Star Receiver17
Star: Physical Interfaces18
Figure 2: Star Physicali18
Cabled System Topology19
Figure 3: Star Systemt19
Wireless Star System Topology20
Figure 4: Wireless Star S20
Star Receiver Installation21
Installation Instructions21
Figure 5: Vesa Interface22
Figure 6: Vesa Interface22
Figure 7: Vesa Interface23
Star Power Supply Installation24
Wall Mount Power Supply24
Figure 8: Star Power Supply24
Enode Installation26
Enode Specifications26
Figure 9: Enode Interfaces26
Table 2: Enode Connector Specification27
Table 3: Enode Operating Specification27
Emux Installation28
About Insertion Loss29
Emux Specifications29
Figure 10: Example Cabling29
Figure 11: Emux Interfaces29
Table 4: Emux Connector Specification30
Table 5: Emux Operating Specification31
Expander Installation32
Figure 12: E Xpanderi32
Enode-Expander Addressing Scheme33
New Enode ID (Present)33
Figure 13: E Node Porto33
Table 6: Expander Operating Specification33
Enode to Expander Exciter ID Encoding34
Figure 14: E Node ID Address34
Figure 15: E Node ID to E X34
Gpio Installation36
Figure 16: Gpio Unit with36
Product Overview37
Figure 17: Gpio Unitt37
Table 7: Gpio Operating Specification37
Figure 18: Gpio Unit Jumper38
Figure 19: Gpio/ E Nodep38
Gpio Cabling40
Figure 20: Gpio Inputt40
Table 8: Gpio Input Terminal Block40
Master Controller Installation41
Figure 21: Mcon Architecture41
Table 9: Mcon Server Specification42
Redundancy Summary43
Figure 22: Front Panel of43
Table 10: Mcon43
Figure 23: Redundantp44
Figure 24: Identification of44
System Network Setup45
Connecting to the Mcon45
Changing Mcon Network Settings45
Figure 25: Mcon Network46
Star Network Setup47
Using a Terminal Session on the MCON Desktop47
Figure 26: Mcon Security47
Figure 27: Mcon Session in48
Figure 28: Mcon Session in49
Figure 29: Adobe Flashp50
Figure 30: Adobe Flashp51
Figure 31: Adobe Flashp52
Figure 32: Save File Dialog52
Figure 33: Mcon Desktop53
Figure 34: Mcon Desktop53
Using an Internet Browser54
Figure 35: Authentication54
Figure 36: Star 3000 Web55
Figure 37: Star Web Ui N55
Change the User Name And/Or Password56
Figure 38: Systemc56
Mcon Configuration58
Appendix A: Fcc Notice, Star 3000 and Enode60
Appendix B: Fcc Notice, Emux62

MOJIX STAR3000 - Product Overview

Table of Contents