MONITOR
HEATING
SYSTEM
Section
2:
Installation
2-1
NOTICE
BEFORE
INSTALLATION
The
heater must
be
installed
by a
qualified
service
person according
to
this installation instruction
.
The
installation must conform with local codes
or,
in
the
absence
of
local codes,
the
National fuel
Gas
Code,
ANSI
Z223.1/NFPA54.
The
installation must conform with local codes
or,
in
the
absence
of
local codes,
the
current
CAN 1 -
B149
INSTALLATION CODE.
For
mobile housing
and
recreational vehicle
installation
the
current
Standard
CSA Z
240.4
GAS
EQUIPPED
RECREATIONAL
VEHICLES
AND
MOBILE HOUSING.
A
manufactured home (mobile home)
installation
must conform with
the
Manufactured Home
Construction
and
Safety
Standard, Title
24
CFR,
Part
3280,
or,
when such
a
standard
is not
applicable,
the
Standard
for
Manufactured Home
installations, ANSI
A
225.1/NFPA
501 A.
Due
to
high
temperatures,
the
appliance
should
be
located
out of
traffic
and
away
from furniture
and
draperies.
Children
and
adults
should
be
alerted
to the
hazards
of
high surface temperatures
and
should
stay
away
to
avoid bums
or
clothing
ignition.
Young
children should
be
carefully supervised
when
they
are in the
same room
as the
appliance.
Clothing
or
other flammable material should
not
be
placed
on or
near
the
appliance.
Make
sure that
the
flow
of
combustion
and
ventilation
air is not
obstructed.
Any
safety
or
guard
removed
for
servicing
an
appliance must
be
replaced prior
to
operating
the
appliance.
A\
WARNING
Do
not
operate appliance with
the
panel removed,
cracked
or
broken. Replacement
of the
panel
should
be
done
by a
licensed
or
qualified
service
person.
Installation
and
repair
should
be
done
by a
qualified
service
person.
The
appliance should
be
inspected
before
use and at
least annually
by a
qualified
service person. More frequent
cleaning
may
be
required
due to
excessive
lint
from
carpeting, bedding material,
etc.
It is
imperative
that control compartments, burners
and
circulating
air
passageways
of the
appliance
be
kept
clean.
Do
not use
this
heater
if any
part
has
been under
water.
Immediately
call
a
qualified service
technician
to
inspect
the
heater
and to
replace
any
part
of the
control system
and any gas
control
which
has
been under water.
The
appliance, when installed, must
be
electrically
grounded
in
accordance
with
local
codes
or, in
the
absence
of
local codes, with
the
National
Electrical Code,
ANSI/NFPA
70 .
The
appliance, when installed, must
be
electrically
connected
and
grounded
in
accordance with local
codes
or, in the
absence
of
local codes, with
the
current
CSA
C22.1 CANADIAN ELECTRICAL
CODE.
/^WARNING
THIS
APPLIANCE
IS
EQUIPPED
WITH
A
THREE-
PRONG
(GROUNDING)
PLUG
FOR
YOUR
PROTECTION
AGAINST
SHOCK
HAZARD
AND
SHOULD
BE
PLUGGED
DIRECTLY
INTO
A
PROPERLY
GROUNDED
THREE-PRONG
RECEPTACLE.
DO NOT CUT OR
REMOVE
THE
GROUNDING
PRONG
FROM
THIS
PLUG.
ZL
WARNING
IN
MANUFACTURED/MOBILE
HOMES
WIRED
FOR
120/240V, ENSURE THAT
THE
GF3800/GF1800
IS
ONLY
PLUGGED
INTO
A
120
VOLT
CIRCUIT.
/K
CAUTION
Before
converting
the
GF3800/GF1800
gas
type
(to
Liquid Propane
or Nat
Gas),
Read
instructions
in
Section
2,
Page
21,
22.
For
manufactured home (USA only)
or
mobile
home
or
residential installation convertible
for use
with
natural
gas and
liquefied
petroleum
gases
when
provision
is
made
for the
simple conver-
sion
from
one gas to the
other.
13
To Next Page
Loading...
