EasyManuals Logo

MSA Ultima Series User Manual

MSA Ultima Series
54 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #4 background imageLoading...
Page #4 background image
INITIAL Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . .2-10
Regular Calibration . . . . . . . . . . . . . . . . . . . . . . . . . .2-11
Zeroing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-11
Spanning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-13
Figure 2-5. Ultima X Unit - Apply SPAN Gas Flag 2-13
Figure 2-4. Ultima Unit - Apply SPAN Gas Flag . .2-13
Figure 2-6. Span Set-up (Ultima unit shown) . . . .2-14
Figure 2-7. Ultima X Series Unit
Calibration End Display . . . . . . . . . . . . . . . .2-15
Figure 2-8. Span Gas Connection
(Ultima unit shown) . . . . . . . . . . . . . . . . . . .2-15
OXYGEN Calibration . . . . . . . . . . . . . . . . . . . . . . . . .2-16
25% Oxygen Ultima/Ultima X Series Gas Monitor . .2-17
XIR Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-17
" WARNING . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-17
Chapter 3,
Controller - Detailed Operation . . . . . . . . . . .3-1
Viewing the Ultima Gas Monitor Display Modes . . . . . .3-1
Table 3-1. (see "Procedures") The Controller Can
Change the Display to Show: . . . . . . . . . . . . .3-1
To View the Status of the Monitor . . . . . . . . . . . . .3-2
Procedures (see TABLE 3-1) . . . . . . . . . . . . . . . . . . . . .3-3
Procedure 1. Setting the Average Time Interval . . . . .3-3
To Change the Average Time Interval . . . . . . . . . . .3-3
Procedure 2. Setting the Span Value . . . . . . . . . . . . .3-3
To Change the Calibration Span Gas Value
of the Ultima Sensor . . . . . . . . . . . . . . . . . . . . . . . .3-3
To Change the Calibration Span Gas Value
of the Ultima X Series Sensor . . . . . . . . . . . . . . . . .3-4
Procedure 3.
Setting the Range on an Ultima X Series Sensor . . . .3-5
Procedure 4
Setting the Gas Table for the Ultima XIR Sensor . . . .3-6
Procedure 5.
Setting the Three
Ultima Gas Monitor Alarm Setpoint Values . . . . . . . . .3-7
ii

Table of Contents

Other manuals for MSA Ultima Series

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the MSA Ultima Series and is the answer not in the manual?

MSA Ultima Series Specifications

General IconGeneral
DisplayLCD with backlight
Communication PortsRS-485, Modbus RTU
Measurement RangeDepends on sensor connected
AccuracyDepends on sensor connected
Outputsrelays
CertificationsUL

Related product manuals