W415-4121 / B / 04.20.23
EN
4
table of contents
1.0 general information 5
1.1 rates and effi ciencies 6
1.2 installation checklist 7
1.3 installation overview 8
1.4 rating plate/lighting instruction
location 10
1.5 mobile home installation 11
1.6 hardware list 11
1.7 lifting handles installation/removal 11
2.0 dimensions 12
3.0 minimum venting requirements 13
3.1 typical venting installation 15
3.2 minimum air terminal location
clearances 17
3.3 horizontal termination (natural gas) 18
3.4 vertical termination
(natural gas) 20
4.0 rough framing - before appliance
installation 21
4.1 minimum framing dimensions 22
4.1.1 minimum clearance to combustible
enclosures 23
4.2 front frame installation 24
5.0 venting installation 25
5.1 fi restop spacer assembly 25
5.2 horizontal installation 27
5.3 vertical installation 28
5.4 using fl exible vent components 29
5.4.1 horizontal air terminal installation 29
5.4.2 vertical air terminal installation 30
5.4.3 appliance vent connection 30
5.5 restricting vertical vents 31
5.5.1 TLV50 31
5.5.2 TLV62 / TLV74 31
5.6 vent shield installation 32
6.0 electrical information 33
6.1 hard wiring connection 33
6.2 receptacle wiring diagram 33
6.3 in the event of a power failure 33
6.4 battery holder/switch installation 34
6.5 initializing the battery holder/switch
for the fi rst time 34
6.6 access panel 35
6.7 wiring diagram 36
6.8 eFIRE application controller 36
6.8.1 TLV50 wiring diagram 37
6.8.2 TLV62 / TLV74 wiring diagram 38
7.0 gas installation 39
8.0 operation 40
8.1 pilot-on-demand 41
9.0 nailing tab installation 42
10.0 finish framing - after appliance
installation 43
10.1 framing with non-combustibles 43
11.0 finishing 45
11.1 fastener placement restriction 45
11.2 fi nishing with non-combustibles 46
11.3 installing non-combustible board 48
11.4 minimum combustible mantel
clearances 49
11.5 TV mounting restrictions (without
DHC™) 50
11.6 safety barrier installation / removal 51
11.7 fi rebox glass door installation /
removal 51
11.8 media installation / removal 53
11.9 media tray removal 54
11.10 adjusting the fi nishing trim 54
12.0 adjustments 55
12.1 restricting vertical vents 55
12.2 venturi adjustment 55
12.3 pilot burner adjustment 56
12.4 fl ame characteristics 56
13.0 maintenance 57
13.1 annual maintenance 58
13.2 control access 58
13.3 burner removal 59
13.4 valve removal 59
13.5 control module removal 60
13.6 LED replacement 61
13.7 glass / door replacement 62
13.8 care of glass 62
13.9 care of plated parts 62
14.0 replacement parts 63
14.1 overview 64
14.2 burner components 65
15.0 troubleshooting 67
16.0 warranty 70
The information throughout this manual is believed to be correct at the time of printing. Wolf Steel Ltd. reserves
the right to change or modify any information within this manual at any time without notice. Changes, other than
editorial are denoted by a vertical line in the margin.
note:
To Next Page
Loading...
