Nikon T-RCP - User Manual

Questions and Answers

D
Daniel RangelAug 19, 2025
Why electrical component doesn’t operate with Nikon T-RCP Remote Control?
- E
  elizabeth41Aug 19, 2025
  If an electrical component doesn't operate with the Nikon Remote Control, it could be due to a couple of reasons: First, the electrical component might not be correctly connected to the HUB controller; to solve this, turn off the power to the HUB controller, disconnect the electrical component, and then reconnect it. Second, the remote control operation might be set to “OFF.” In this case, you should set the remote control operation to “ON”.
D
Dylan SweeneyAug 21, 2025
What to do if dia-illumination lamp cannot be turned ON or OFF with Nikon T-RCP?
- M
  Matthew WilsonAug 21, 2025
  If the dia-illumination lamp cannot be turned ON or OFF, there are several potential causes. First, the dia-illumination lamp power supply may not be correctly connected to the HUB controller; to resolve this, turn OFF the power of the HUB controller, disconnect the dia-illumination lamp power supply, and then reconnect it. Second, the EXTERNAL switch of the dia-illumination lamp power supply might be OFF; in this case, turn ON the EXTERNAL switch. Finally, the remote control operation may be set to “OFF”; if so, set the remote control operation to “ON”.
M
mtravisAug 23, 2025
What to do if voltage of dia-illumination lamp cannot be adjusted with Nikon T-RCP?
- J
  John LeonardAug 25, 2025
  If the voltage of the dia-illumination lamp cannot be adjusted, there are several possible reasons. First, the dia-illumination lamp power supply may not be correctly connected to the HUB controller; to fix this, turn OFF the power to the HUB controller, disconnect the dia-illumination lamp power supply, and reconnect it. Second, the EXTERNAL switch of the dia-illumination lamp power supply might be OFF; if so, turn ON the EXTERNAL switch. Third, the remote control operation may be set to “OFF”; ensure it is set to “ON.” Lastly, the dia-illumination lamp might be OFF; in this case, turn ON the dia-illumination lamp.
T
Tamara MayerAug 26, 2025
Why is dia-illumination lamp voltage not indicated on Nikon Remote Control?
- K
  Kristen WilliamsAug 26, 2025
  If the dia-illumination lamp voltage is not indicated, there could be a few reasons: The dia-illumination lamp power supply may not be correctly connected to the HUB controller. To solve this, turn OFF the power to the HUB controller, disconnect the dia-illumination lamp power supply from the HUB controller, and then reconnect it. Another possible cause is that the EXTERNAL switch of the dia-illumination lamp power supply is OFF. If this is the case, turn ON the EXTERNAL switch of the dia-illumination lamp power supply. Also, the remote control operation may be set to “OFF.” If so, set the remote control operation to “ON”.
P
pfarleyAug 28, 2025
How to fix Nikon T-RCP when objective information is not indicated?
- V
  Victoria CarpenterAug 28, 2025
  If the objective information is not indicated, it could be due to the revolving nosepiece not being correctly connected to the HUB controller. To resolve this, turn OFF the power to the HUB controller, disconnect the revolving nosepiece from the HUB controller, and then reconnect it. Another reason could be that the indication of information for the objective is OFF; in this case, turn ON the indication function for the information on the objective.
M
Mark MaysAug 30, 2025
What to do if Nikon Remote Control pad doesn’t start up?
- T
  Timothy MercerAug 30, 2025
  If the remote control pad doesn’t start up (the TITLE screen appears and freezes), the remote control pad may not be connected to the HUB controller correctly. To fix this, turn OFF the power to the HUB controller, disconnect the remote control pad from the HUB controller, and then reconnect it.
D
Dennis SmithSep 1, 2025
How to fix Nikon T-RCP Remote Control when Z-axis coordinates are not indicated?
- P
  Paige MuellerSep 1, 2025
  If the Z-axis coordinates are not indicated, it could be because the HUB controller is not correctly connected to the microscope. In this case, turn OFF the power to the HUB controller and check that the HUB controller is correctly connected to the microscope. Alternatively, the indication of Z-axis coordinates might be OFF; if so, turn ON the indication function for Z-axis coordinates.
D
donnawardSep 3, 2025
How to fix Nikon T-RCP Remote Control when condenser module information is not indicated?
- S
  susan82Sep 3, 2025
  If the condenser module information is not indicated, it could be due to the condenser module changeover not being correctly connected to the HUB controller. To solve this, turn OFF the power to the HUB controller, disconnect the condenser module changeover from the HUB controller, and then reconnect it. Alternatively, the indication of the information for the condenser module might be OFF; if so, turn ON the indication function for the information on the condenser module.
Q
qgibbsSep 5, 2025
How to fix Nikon T-RCP Remote Control when filter block information is not indicated?
- V
  Veronica JohnsonSep 5, 2025
  If the filter block information is not indicated, it could be because the filter block changeover is not correctly connected to the HUB controller. To resolve this, turn OFF the power to the HUB controller, disconnect the filter block changeover from the HUB controller, and then reconnect it. Another possibility is that the indication of the information for the filter block is OFF; in this case, turn ON the indication function for the information for the filter block.
K
Kevin TuckerSep 7, 2025
How to fix Nikon T-RCP Remote Control when excitation filter information is not indicated?
- R
  Richard EllisSep 7, 2025
  If the excitation filter information is not indicated, it may be that the excitation filter changeover is not correctly connected to the HUB controller. To solve this, turn OFF the power to the HUB controller, disconnect the excitation filter changeover from the HUB controller, and then reconnect it. Another reason could be that the indication of the information for the excitation filter is OFF; if so, turn ON the indication function for the information on the excitation filter.