The range of this parameter is Off, 32 Triplet, 32nd, 16th Triplet, 16th, 8th Triplet, 16th Dotted, 8th, 4th Triplet, 8th Dotted, 4th, 2nd
Triplet, 4th Dotted, 2nd, 1 Bar Triplet, 2nd Dotted, 1 Bar, 2 Bar Triplet, 1 Bar Dotted, 2 Bars, 4 Bar Triplet, 3 Bars, 5 Bar Triplet, 4
Bars, 3 Bar Dotted ( 4.5 Bars ), 7 Bar Triplet, 5 Bars, 8 Bar Triplet, 6 Bars, 7 bars, 5 Bar Dotted ( 7.5 Bars), 8 Bars, 6 Bar Dotted (
9 Bars ), 7 Bar Dotted ( 10.5 bars ) & 8 Bar Dotted ( 12 Bars ). This parameter is memorised with a Program in Program Mode or
memorised with a Program or Performance in Performance Mode depending on the value of the Part’s “Effects Used” parameter.
If this parameter is set to anything but “Off”, the Delay Time parameter will not work.
As can be seen the lower parameter is “Delay HF damp”. In this case with a value of 20.
This parameter determines the rate at which High Frequencies decay away in repeats of the Delay. Use the lower Fast Data knob
to adjust this parameter. The range of this parameter is 000 to 127. This parameter is memorised with a Program in Program Mode
or memorised with a Program or Performance in Performance Mode depending on the value of the Part’s “Effects Used” parame-
ter.
Page 4 looks like so:
As can be seen the higher parameter is “Delay Wheel”. In this case with a value of +20.
This parameter determines how much the Mod Wheel controls the amount of Delay effect. Use the higher Fast Data knob to adjust
this parameter. Fully anticlockwise, the Delay will be reduced with full modulation of the Mod Wheel. Fully clockwise, the Delay will
be increased with full modulation of the Mod Wheel. The range of this parameter is -64 to +63. This parameter is memorised with a
Program in Program Mode or memorised with a Program or Performance in Performance Mode depending on the value of the
Part’s “Effects Used” parameter.
Menu - Button ( Reverb selected )
When this button is pressed, a series of pages is available on the display containing parameters relevant to this section.
In the Reverb section there are 3 pages available. These are selected using the Page Up & Page Down buttons to the left of the
display.
There are a maximum of 2 parameter’s displayed on any page. One for each line on the display. The “Fast Data” Knobs on the
right of the display are used to alter these parameters values.
Page 1 looks like so:
As can be seen the higher parameter is “Type”. In this case with a value of Gated reverse.
This parameter determines the type of Reverb effect. Use the higher Fast Data knob to adjust this parameter. There are 16 differ-
ent types of reverb available in the Nova. Turning the higher Fast Data knob fully anticlockwise selects Gated reverse reverb. This
is a special reverb where the reverb builds to a point & then stops as opposed to decaying away like normal reverb. Turning the
Fast Data knob clockwise one click selects Gated rising, again this is a gated type of reverb that is slightly reverse in characteristic.
Turning the Fast Data knob clockwise one click selects Gated gentle which is a classic gated sort of reverb. Turning the Fast Data
knob clockwise one click selects Gated falling which is a gated type of reverb but does decay away slightly like normal
reverb.Turning the Fast Data knob clockwise one click selects Dry chamber. This is the first of the normal reverb types & repre-
sents a very small room. The rest of the reverbs model rooms that gradually get bigger & bigger, the last one being Large plate 2.
The range of this parameter is Gated reverse, Gated rising, Gated gentle, Gated falling, Dry chamber, Echo chamber, Small room,
Big room, Medium type 1, Medium type 2, Medium plate 1, Medium plate 2, Large type 1, Large type 2, Large plate 1 & Large
plate 2. This parameter is memorised with a Program in Program Mode or memorised with a Program or Performance in
Performance Mode depending on the value of the Part’s “Effects Used” parameter.
Type Gated reverse
Early ref level 6
Delay wheel +20
To Next Page
Loading...
