Oakton CON 11 - Page 58

80 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

Instruction Manual CON 11/110

54

Figure 47: Click on 'Browse' button and locate CD-ROM drive

Figure 48 : Locate the CyberComm Portable Setup program in the CD-ROM under "Eutech

DAS" directory.

Table of Contents

Default Chapter3
- Table of Contents3
1 Introduction5
2 Display and Keypad Functions6
- Display6
- Keypad7
3 Preparation9
- Inserting the Batteries9
- Conductivity Electrode Information10
- Connecting the Electrode to the Meter11
- Attaching the Electrode Holder to the Meter12
  - Inserting the Electrode into the Electrode Holder12
- Connecting the Ac/DC Adapter13
- Connecting the Rs232C Cable (Only for con 110)13
  - RS232C Configuration14
4 Calibration15
- Important Information on Meter Calibration15
- Preparing the Meter for Calibration16
- T Emperature16
- Temperature Calibration17
- Selection of Automatic or Manual Calibration18
  - A Utomatic18
  - Manual18
- Automatic Calibration (for Conductivity Calibration Only)19
- Manual Calibration (for Conductivity & TDS Calibration)21
- Tds Calibration22
5 Measurement24
- Automatic Temperature Compensation24
- Manual Temperature Compensation25
  - Setting the Manual Temperature Compensation Value26
  - Using26
- Taking Measurements27
  - Taking Measurements with READY Indicator Selected on27
  - Taking Measurements with the Auto HOLD Feature Selected on27
- Using Manual Ranging Function28
  - Selecting Manual Range28
- Hold Function29
6 Memory Function30
- Memory Input30
- Memory Recall31
7 Print Function (for con 110 Only)32
- Using con 110 Meter with Printer or Computer32
- Sending Data to Computer or Printer33
8 Advanced Setup Function38
- Advanced Setup Mode Overview40
- P1.0: Unit Configuration (Cof)42
- P2.0: Viewing Calibration Data46
- P3.0 Viewing Electrode Data47
- P4.0: Auto off48
- P5.0: Reset to Factory Defaults49
  - P5.1: Calibration Reset49
  - P5.2: User Reset50
- P6.0: Memory Clear51
- P7.0: Temperature52
  - P7.1: Setting the Temperature Coefficient52
  - P7.2: Setting the Normalisation Temperature53
- P8.0: Selection of Cell Constant54
- P9.0: Automatic and Single Point Calibration55
  - P9.1: Selection of Automatic or Manual Calibration55
  - P9.2: Selection of Single or Multi Point Calibration56
9 Cybercomm Portable das (for con 110 Only)57
- System Requirements57
- Loading Cybercomm Portable das57
- Running Cybercomm Portable63
- Capturing and Printing Data into Computer Using Data Acquisition67
- Trouble-Shooting Guide68
10 Electrode Care and Maintenance69
11 Error Messages70
12 Trouble Shooting71
13 List of Accessories72
- Replacement Meter and Meter Accessories72
- Calibration Solutions72
14 Factory Default Settings73
- Con 11 Factory Default Setting73
- Con 110 Factory Default Setting74
15 Specifications75
16 Calibration Tips77
17 Calculating Tds Conversion Factors77
18 Calculating Temperature Coefficients78
19 Warranty79
20 Return of Items79

Related product manuals

Preview: Oakton pH 5+

Preview: Oakton 450 Series

Oakton 450 Series

Preview: Oakton 700 Series

Oakton 700 Series

Preview: Oakton 150 Series

Oakton 150 Series

Preview: Oakton Ion 510 Series

Oakton Ion 510 Series

Preview: Oakton WP PCD 650

Oakton WP PCD 650

Preview: Oakton Bench 2700 Series

Oakton Bench 2700 Series

Preview: Oakton PC 700

Preview: Oakton EcoTestr pH1

Oakton EcoTestr pH1

Preview: Oakton T100WL

Preview: Oakton pH 610