Oakton CON 11 - Page 8

80 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

Instruction Manual CON 11/110

4

MODE

MEAS

CAL

ENTER

HOLD

MRMI

SETUP

RANGE

OFF

ON

MI MR

SETUP MODE

MEAS

CAL

ENTER

HOLD

OFF

ON

RANGE

Keypad for CON 11 meter Keypad for CON 110 meter

Figure 2: CON 11 and CON 110 keypads

Table of Contents

Default Chapter3
- Table of Contents3
1 Introduction5
2 Display and Keypad Functions6
- Display6
- Keypad7
3 Preparation9
- Inserting the Batteries9
- Conductivity Electrode Information10
- Connecting the Electrode to the Meter11
- Attaching the Electrode Holder to the Meter12
  - Inserting the Electrode into the Electrode Holder12
- Connecting the Ac/DC Adapter13
- Connecting the Rs232C Cable (Only for con 110)13
  - RS232C Configuration14
4 Calibration15
- Important Information on Meter Calibration15
- Preparing the Meter for Calibration16
- T Emperature16
- Temperature Calibration17
- Selection of Automatic or Manual Calibration18
  - A Utomatic18
  - Manual18
- Automatic Calibration (for Conductivity Calibration Only)19
- Manual Calibration (for Conductivity & TDS Calibration)21
- Tds Calibration22
5 Measurement24
- Automatic Temperature Compensation24
- Manual Temperature Compensation25
  - Setting the Manual Temperature Compensation Value26
  - Using26
- Taking Measurements27
  - Taking Measurements with READY Indicator Selected on27
  - Taking Measurements with the Auto HOLD Feature Selected on27
- Using Manual Ranging Function28
  - Selecting Manual Range28
- Hold Function29
6 Memory Function30
- Memory Input30
- Memory Recall31
7 Print Function (for con 110 Only)32
- Using con 110 Meter with Printer or Computer32
- Sending Data to Computer or Printer33
8 Advanced Setup Function38
- Advanced Setup Mode Overview40
- P1.0: Unit Configuration (Cof)42
- P2.0: Viewing Calibration Data46
- P3.0 Viewing Electrode Data47
- P4.0: Auto off48
- P5.0: Reset to Factory Defaults49
  - P5.1: Calibration Reset49
  - P5.2: User Reset50
- P6.0: Memory Clear51
- P7.0: Temperature52
  - P7.1: Setting the Temperature Coefficient52
  - P7.2: Setting the Normalisation Temperature53
- P8.0: Selection of Cell Constant54
- P9.0: Automatic and Single Point Calibration55
  - P9.1: Selection of Automatic or Manual Calibration55
  - P9.2: Selection of Single or Multi Point Calibration56
9 Cybercomm Portable das (for con 110 Only)57
- System Requirements57
- Loading Cybercomm Portable das57
- Running Cybercomm Portable63
- Capturing and Printing Data into Computer Using Data Acquisition67
- Trouble-Shooting Guide68
10 Electrode Care and Maintenance69
11 Error Messages70
12 Trouble Shooting71
13 List of Accessories72
- Replacement Meter and Meter Accessories72
- Calibration Solutions72
14 Factory Default Settings73
- Con 11 Factory Default Setting73
- Con 110 Factory Default Setting74
15 Specifications75
16 Calibration Tips77
17 Calculating Tds Conversion Factors77
18 Calculating Temperature Coefficients78
19 Warranty79
20 Return of Items79

Related product manuals

Preview: Oakton pH 5+

Preview: Oakton 450 Series

Oakton 450 Series

Preview: Oakton 700 Series

Oakton 700 Series

Preview: Oakton 150 Series

Oakton 150 Series

Preview: Oakton Ion 510 Series

Oakton Ion 510 Series

Preview: Oakton WP PCD 650

Oakton WP PCD 650

Preview: Oakton Bench 2700 Series

Oakton Bench 2700 Series

Preview: Oakton PC 700

Preview: Oakton EcoTestr pH1

Oakton EcoTestr pH1

Preview: Oakton T100WL

Preview: Oakton pH 610