Omron E5AR - MANUAL 2 User Manual

Appendix
A-18
Appendix
CompoWay/F
Setting data
Attributes
Variable type
Address Address
Modbus
Character Setting (monitor) value Character
Default
value
Decimal point
position
Units
Set value
CD 0000
0001 0003 0004 0005 0006
000F
0010 0011 0012 0013
0D00 0D02 0D06 0D08
0D0A
0D0C
0D1E
0D20 0D22 0D24 0D26
o1-t o3-t
co1-t co2-t co3-t co4-t
sl-h sl-l mode ore clfl
H'00000000: Pulse voltage output (0) H'00000001: Linear current output (1) H'00000000: Pulse voltage output (0) H'00000001: Linear current output (1) H'00000000: 0 to 20 mA (0) H'00000001: 4 to 20 mA (1) H'00000000: 0 to 20 mA (0) H'00000001: 4 to 20 mA (1) H'00000000: 0 to 20 mA (0) H'00000001: 4 to 20 mA (1) H'00000000: 0 to 20 mA (0) H'00000001: 4 to 20 mA (1) SP setting lower limit + 1 to input range upper limit (temperature) SP setting lower limit + 1 to H'0001869F (lesser of 99999 or display value equivalent of input upper limit) (analog) Lower limit of input range to SP lower limit - 1 (temperature) Larger of H'FFFFB1E1 (-19999) and display value equivalent of input lower value to SP upper limit - 1 (analog) 1-input type, 4-input type H'00000000: Standard (0) H'00000001: Heat/cool (1) 2-input type H'00000000: Standard (0) H'00000001: Heat/cool (1) H'00000002: Remote SP standard (2) H'00000003: Remote SP heating/cooling (3) H'00000004: Proportional (4) H'00000005: Cascade standard (5) H'00000006: Cascade heating or cooling (6) H'00000000: Reverse action: OR-R (0) H'00000001: Direct action: OR-D (1) H'00000000: Floating: FLOAT (0) H'00000001: Close: CLOSE (1)
0 to 1 0 to 1 0 to 1 0 to 1 0 to 1 0 to 1
Same as at left Same as at left
−
or-r, or-d float, close
0 0 1 1 1 1
1300.0
*1
-200.0
*1
0
Reverse
action
Floating
−
− − − − −
EU EU
−
− −
−
− − − − −
According to
input type
According to
input type
−
− −
Common Common Common Common Common Common
CH CH
Common
CH CH
Output 1 type Output 3 type Linear current output 1 type Linear current output 2 type Linear current output 3 type Linear current output 4 type SP upper limit SP lower limit Control mode Forward/reverse operation Closed/floating
Control initial setting level
"H' -" indicated in set values (monitor values) are values set by communication (monitor).
*1 .... When the input type, temperature units, or scaling display value is changed, settings are initialized as follows:
Temperature input: Set upper and lower limits of sensor input Analog input: Scaling display value 1 (lower limit), 2 (upper limit)

Omron E5AR - MANUAL 2 Specifications

General

Brand	Omron
Model	E5AR - MANUAL 2
Category	Controller
Language	English