What does '[Memory Switch Corrupted]' mean on Omron NT31 Touch terminals and how can I solve it?
The '[Memory Switch Corrupted]' message on your Omron Touch terminals indicates that the memory switches have been initialized due to discovery of an error in the memory switch settings. Set the memory switches again using the System Menu and the “System” settings under “PT Configuration” at the Support Tool.
Why is the Device Monitor function not working on my Omron Touch terminal?
The Device Monitor function might not be working due to incorrect communications settings, the PLC not supporting the function, or the system program installed in the PT being for a PLC maker other than OMRON. Set the communications method as follows when using the Device Monitor function. With C-series PLCs: 1:1 NT Link or 1:N NT Link With CS/CJ-series PLCs: 1:N NT Link (standard or high-speed). Check the model of PLC you are using. Install a system program that supports the Device Monitor function.
What causes the buzzer to sound and the RUN LED to be OFF on Omron Touch terminal?
If the buzzer has sounded and the RUN LED is OFF on your Omron Touch terminal, it could be due to malfunction caused by external noise or the NT31/NT31 has developed trouble. Carry out grounding work or contact your OMRON service center.
How to resolve '[Memory Switch Corrupted]' error on Omron Touch terminal?
The '[Memory Switch Corrupted] Because Memory Switch setting was last' error appears because the memory switches have been initialized due to discovery of an error in the memory switch settings. Set the memory switches again using the System Menu and the System settings under PT Configuration at the Support Tool. If the problem recurs, contact your OMRON service center.
How to fix Omron Touch terminals when the power LED fails to come ON?
If the power LED on your Omron Touch terminal doesn't light up, first ensure the device is correctly connected to a power source. If the connection is correct, but the LED still doesn't turn on, it's possible the power supply fuse has blown, in this case you should contact your OMRON service center.
Why the graph display does not change on Omron NT31 Touch terminals?
If the graph display on your Omron Touch terminal isn't changing, one of the percentage display settings — ?100%, 0%, or 100% — might be incorrect. Ensure these values are set in the following relationship: ?100% value < 0% value < 100% value.
Why cannot switch screens with touch switches on Omron NT31 Touch terminals?
If you cannot switch screens with touch switches on your Omron Touch terminal, it might be because bit 4 of the PT status control area (PT screen switching) is set to 1 (ON). Set bit 4 to 0 (OFF).
What does '[With memory switch setting screen] Invalid Comm. Method' mean on Omron NT31 Touch terminals?
If your Omron Touch terminal displays the message '[With memory switch setting screen] Invalid Comm. Method', it indicates that protocol settings for serial port A and serial port B are mismatched. Refer to Possible Combinations of Communication Method Settings and set the protocol of serial port A and serial port B so that their settings are matched. Set serial port A to None when connecting the Support Tool and the host at the same time.
What does '[No Screen Data]' mean on Omron Touch terminals and how to resolve it?
The '[No Screen Data]' error on your Omron Touch terminals means that no screen data is registered. To resolve this, transmit screen data from the Support Tool.
How to resolve '[Programming Console Error] Programming Console Function does not RUN' error on Omron Touch terminal?
The '[Programming Console Error] Programming Console Function does not RUN' error appears because the connecting cable is defective, there is malfunction due to external noise, or a Programming Console is connected. Check the cable connection and perform a conductivity test. If there is a fault, replace the cable. Carry out grounding work. Disconnect the Programming Console.
General| Display Type | STN LCD |
|---|---|
| Touch Panel | Analog resistive |
| Communication Interface | RS-232C, RS-422/485 |
| Power Supply | 24 VDC |
| Operating Temperature | 0 to 50 °C |
| Storage Temperature | -20 to 60 °C |
| Display Size | 5.7 inch |
| Resolution | 320 x 240 pixels |
| CPU | 32-bit RISC |
| Humidity | 10 to 90% RH (non-condensing) |
| Shock Resistance | 15 G for 11 ms |
| Protection class | IP65 (front panel) |
To Next Page
