Onan P216 User Manual

P224
DESCRIPTION
CYLINDER BLOCK
Maximum Allowable
Main Bearing Inside Diameter (Without bearing)
.............
Main Bearing Inside Diameter (Installed) ....................
Cylinder Bore Honed Diameter ............................
Taper .................................................
0 u t-of- Roun d
.........................................
Camshaft Bearing Bore (Bearing Installed) ..................
CRANKSHAFT
Main Bearing Journal Diameter ............................
Main Bearing Clearance ..................................
Connecting Rod Journal Diameter .........................
Crankshaft End Play ......................................
CONNECTING ROD
Large Bore Diameter (Without bearing installed and rod bolts
Connecting
Rod Side Clearance ...........................
Piston Pin Bushing Bore (Without bushing) ..................
properly torqued) .......................................
Piston Pin Bushing Bore (Finished bore) ....................
Bearing to Crankshaft Clearance ...........................
CAMSHAFT
Bearing Journal Diameter .................................
Bearing Clearance .......................................
End Play ................................................
Intake., ...............................................
Exhaust ...............................................
Lobe Height
PISTON
Clearance in Cylinder
Measure 90"
to pin 1.1 87 inch below top of piston .........
Piston Pin Bore ..........................................
Ring Groove Width
Top Compression Ring
.................................
Middle Compression Ring ...............................
Bottom Oil Control Ring .................................
PISTON PIN
Clearance in Piston ......................................
Clearance in Connecting Rod .............................
Diameter ................................................
PISTON RINGS
Clearance
Top Groove
...........................................
Ring End Gap in Cylinder .................................
MINIMUM
Inches
3.5625
2.1 870
2.001
5
1.3757
1.9992
0.0024
1.6252
0.0060
1.7505
0.0020
0.81 15
0.7504
0.0020
1.3740
0.001 5
0.01 10
0.0070
0.7502
0.0800
0.0800
0.1 880
0.00004
0.0002
0.7500
0.0020
0.01
00
(mm)
(90.49)
(55.55)
(34.94)
(50.84)
(50.78)
(0.061)
(41.28)
(0.1 52)
(44.46)
(0.051)
(20.61)
(19.06)
(0.051)
(34.90)
(0.038)
(0.279)
1.1 670
1.1 570
(0.1 78)
(1 9.06)
(2.032)
(2.032)
(4.775)
(0.001)
(0.005)
(1 9.05)
(0.051)
(0.254)
MAXIMUM
Inches
3.5635
0.003
0.003
2.1 880
2.0040
1.3787
2.0000
0.0042
1.6260
0.01
20
1.751 0
0.01 60
0.81 25
0.7508
0.0033
1.3745
0.0030
0.0480
(29.64)
(29.39)
0.0090
0.7506
0.081
0
0.081 0
0.1 890
0.00064
0.0008
0.7502
0.0080
0.0200
(mm)
(90.51)
(0.08)
(0.08)
(55.58)
(50.90)
(35.02)
(50.80)
(0.1 07)
(41.30)
(0.305)
(44.48)
(0.406)
(20.64)
(1 9.07)
(0.084)
(34.91)
(0.076)
(1.219)
(0.229)
(1 9.07)
(2.057)
(2.057)
(4.801)
(0.01 6)
(0.020)
(1 9.06)
(0.203)
(0.508)
3-3

Onan P216 Specifications

General

Cylinders	2
Cooling System	Air-cooled
Fuel Type	Gasoline
Power Output	16 hp
Ignition System	Electronic
Starting System	Electric
Engine Type	4-cycle, air-cooled
Oil Capacity	2 U.S. quarts (1.9 liters)