Need help?Do you have a question about the Optoma EX765 and is the answer not in the manual?
General| Matrix size | 0.55 \ |
|---|---|
| Number of colors | 134 million colors |
| Native aspect ratio | 4:3 |
| Projection distance | 1.2 - 10 m |
| Vertical scan range | 50 - 85 Hz |
| Horizontal scan range | 15 - 91.1 kHz |
| Projection technology | DLP |
| Supported aspect ratios | 4:3, 16:9 |
| Contrast ratio (typical) | 2500:1 |
| Screen size compatibility | 0.57 - 7.72 \ |
| Projector native resolution | XGA (1024x768) |
| Keystone correction, vertical | -40 - 40 ° |
| Throw ratio | 1.62 - 2.64:1 |
| Focal length range | 18.39 - 29.42 mm |
| Aperture range (F-F) | 2.41 - 3.2 |
| Lamp power | 280 W |
| Light source type | Lamp |
| Service life of light source | 4000 h |
| RMS rated power | 4 W |
| Serial interface type | RS-232 |
| USB 2.0 ports quantity | USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them. |
| S-Video inputs quantity | 1 |
| VGA (D-Sub) ports quantity | 3 |
| Component video (YPbPr/YCbCr) in | - |
| Maximum analog resolution | 1600 x 1200 pixels |
| Ethernet LAN | No |
| Noise level | 28 dB |
| Power source | AC |
| AC input voltage | 100 - 240 V |
| AC input frequency | 50 - 60 Hz |
| Power consumption (standby) | 1 W |
| Power consumption (typical) | 233 W |
| Operating altitude | 0 - 3000 m |
| Operating temperature (T-T) | 5 - 40 °C |
| Operating relative humidity (H-H) | 0 - 85 % |
| Supported video modes | 1080i, 480i, 480p, 576i, 576p, 720p |
| Analog signal format system | NTSC, NTSC 3.58, NTSC 4.43, NTSC M, PAL, PAL B, PAL D, PAL G, PAL H, PAL I, PAL M, PAL N, SECAM, SECAM B, SECAM D, SECAM G, SECAM K, SECAM K1, SECAM L |
| Placement | Desktop, Ceiling |
| Product type | Standard throw projector |
| Product color | Black |
| Sustainability certificates | RoHS |
Weight and Dimensions| Depth | 283 mm |
|---|---|
| Width | 364 mm |
| Height | 127 mm |
| Weight | 4600 g |
Step-by-step instructions for removing the lamp cover and module.
Detailed steps for removing the top cover of the projector.
Instructions on how to remove the back cover of the projector.
Procedures for safely removing the main board from the projector.
Detailed instructions for removing the lamp driver module.
Comprehensive guide for disassembling the projector's engine module.
Procedures for removing the bottom cover of the projector.
Steps to access engineering mode and reset lamp usage hours.
Provides troubleshooting procedures for common projector issues like no power or auto shut down.
Methods for measuring optical performance like brightness and contrast.
Procedures for testing and configuring the projector's network connectivity.
Procedures for testing the wireless connectivity and functionality.
Guidelines and steps for performing firmware upgrades.
Instructions for installing the DLP Composer Lite software.
Steps to install the necessary USB drivers for firmware updates.
Detailed procedure for upgrading projector firmware via USB.
Specific instructions for upgrading the 8051 firmware.
Instructions for setting up the NLINK software for firmware updates.
Steps to install the Manley USB driver for firmware flashing.
Procedure for performing the 8051 firmware upgrade using NLINK.
Instructions for upgrading projector firmware over a network connection.
Procedure for upgrading projector firmware over the network.
Specific instructions for upgrading the projector's wireless firmware.
Procedure for upgrading the projector's wireless firmware.
To Next Page
