Panasonic AW-HE130W - Basic Shooting Operations; How to Turn the Power on and off; Turning The Power On; Turning The Power Off

Basic shooting operations
1. Set the subject brightness to the appropriate level.
2. Turn on the power of all the units and devices in the
system.
3. Select the unit to be operated.
Evenwhenusingonlyoneunit,itmuststillbeselectedfromthe
wirelessremotecontrolorcontroller.
4. Select the shooting mode.
Oneoffourshootingmodes(Scene1,Scene2,Scene3orScene4)
—whicheveronewillbestsuittheshootingconditions—canbe
selected.
Theshootingmodesaresetbytheuser.
Fordetailsofthefactorysettings,refertopages61to63.
Selectthemodethatsatisfiestheshootingconditionsandsuitsyour
preferences.
Whencontinuingtoshootinthesamecircumstances,thereisno
needtoselectanothermode.
5. Start shooting.
(After shooting, turn off the power of all the units and
devices in the system.)
<NOTE>
• Someoftheinitialsettingsareautosettingsandcannotbeoperated
manually.Tooperatethemmanually,switchfromtheautosettingsto
themanualsettingsasrequired.
Ifthesettingshavealreadybeenchangedandtheoriginalsettingsare
toberestored,refertothe“Whattodowhenencounteringproblems
inthebasicshootingoperations”(→page29)and“Camerascreen”(→
page48)in“Cameramenuitems”.
How to turn the power on and off
Turning the power on
When performing operations from a wireless
remote control
1. Set all the power switches of the units and devices
connected in the system to ON.
• Thisunitdoesnothaveapowerswitch.
Whenpowerissuppliedtoit,thestatusdisplaylampwilllightup
orange,andtheunitissettothestandbymode.
2. Press one of the <CAM1> to <CAM4> buttons on the
wireless remote control to select the unit.
3. Press the <ON/STANDBY> button on the wireless remote
control for 2 seconds.
ThePOWERONmodeisestablished,imagesareoutput,andcontrol
canbeexercised.
• Theunit’sstatusdisplaylampnowlightsupgreen.
<NOTE>
• Ittakesmaximum30secondsperunitfortheinitialsettings
operationtobecompleted.Duringthisperiod,theunitcannotbe
operated.
(Statusdisplaylamp:lightuporange)
4. If a multiple number of units are going to be used, repeat
steps 2 and 3 as required.
Theunit’sstatusdisplaylampblinksgreenwhenasignalmatchedby
theremotecontrolIDhasbeenreceived,anditblinksorangewhena
signalthatisnotmatchedbytheremotecontrolIDhasbeenreceived.
<NOTE>
• WhenoperationistransferredtotheSTANDBYmode:
Thecurrentzoom,focusandirispositionsarestoredinthememory
(POWERONpreset).
• WhenoperationistransferredtothePOWERONmode:
Thezoom,focusandirisareadjustedtothepositionswhichwere
storedinthememory(POWERONpreset)whenoperationwas
transferredtotheSTANDBYmode.
When performing operations from a controller
When using a AW-RP50, AW-RP120, or AK-HRP200
Refertotheoperatinginstructionsforthecontroller.
When using a commercially available controller
Refertotheoperatinginstructionsforthecontroller.
Turning the power off
When performing operations from a wireless
remote control
1. Press one of the <CAM1> to <CAM4> buttons on the
wireless remote control to select the unit.
2. Press the <ON/STANDBY> button on the wireless remote
control for 2 seconds.
TheunitentersSTANDBYmode.
• Theunit'sstatusdisplaylamplightsorangeduringthistime.
3. If a multiple number of units are going to be used, repeat
steps 1 and 2 as required.
4. Set all the power switches of the units and devices
connected in the system to OFF.
• Thisunitdoesnothaveapowerswitch.
<NOTE>
• WhenoperationistransferredtotheSTANDBYmode:
Thecurrentzoom,focusandirispositionsarestoredinthememory
(POWERONpreset).
• WhenoperationistransferredtothePOWERONmode:
Thezoom,focusandirisareadjustedtothepositionswhichwere
storedinthememory(POWERONpreset)whenoperationwas
transferredtotheSTANDBYmode.
When performing operations from a controller
When using a AW-RP50, AW-RP120, or AK-HRP200
Refertotheoperatinginstructionsforthecontroller.
When using a commercially available controller
Refertotheoperatinginstructionsforthecontroller.
24
25