Panasonic AW-HE130W - Operations On The Aw-Rp50 Remote Camera Controller

Operations on the AW-RP50 Remote Camera Controller
POWER ALARM F1 CAMERA
OSD
R/B GAIN R/B PED
SYSTEMSETUPCAMERA
SCENE/MODE
DETAIL
DELETESTORE
PAGEMENU F2 EXIT
USER2USER1
PT ACTIVEAUTOIRIS
AUTO
HILOW
PTZ/FOCUS SPEEDFOCUS/PUSH OAF
TELE
ZOOM
WIDE
CAMERA STATUS / SELECTION
PRESET MEMORY / MENU
GAIN/PED
F2
F1
1 2 3
AWB/ABB
4
SHUTTER
5
1 2 3 4 5
6 7 8 9 10
For operating the camera menus.
CAMERAOSD:
 Whenthisispressedfor2
seconds,theselectedcamera
menuisdisplayed,overlapping
thecameraoutputimage.When
itispressedfor2secondswhile
acameramenuisdisplayed,the
menuisexited.
F1: Turntomovethecursorupand
downinthecameramenuorto
changesettingvalues.Pressto
movetothenextlevelofamenu
itemortochangeasettingvalue
atthelowestlevel.
Selects a camera to be operated.

Camera menu operation
1. Press the appropriate <CAMERA STATUS/SELECTION>
button to select the unit you want to operate.
2. Press and hold the <CAMERA OSD> button on the AW-
RP50 for about 2 seconds.
TheAW-HE130cameramenuappearsonthemonitor.
3. Turn the <F1> dial to select an AW-HE130 camera menu
item or to change a setting value.
Turnthe<F1>dialtomovethecursorupanddownortochange
settingvalues.
Pressthe<F1>dialtomovetothenextlevelofamenuitemorto
changeasettingvalueatthelowestlevel.
4. To exit the camera menu, press and hold the <CAMERA
OSD> for about 2 seconds.

Switching between day and night mode
1. Press the <MENU> button on the AW-RP50.
The<MENU>buttonlights,andthe<PRESETMEMORY/MENU>
buttonsbecomeselectable.
2. Press the <9 (SETUP)> button in the <PRESET MEMORY/
MENU> area.
Thebuttonlights,andthe[SETUP]menuappearsontheLCDpanel.
3. Turn the <F1> dial to select [FUNCTION], then press the
<F1> dial.
4. Turn the <F1> dial to select [OPTION].
[Off]or[On]appearsonthebottomright(F2area)oftheLCDpanel.
5. Turn the <F2> dial to select [Off] or [On], then press the
<F2> dial.
[Off]:Daymode
[On]:Nightmode

Color temperature setting (COLOR TEMP)
1. Press the <MENU> button on the AW-RP50.
The<MENU>buttonlights,andthe<PRESETMEMORY/MENU>
buttonsbecomeselectable.
2. Press the <4 (AWB/ABB)> button in the <PRESET
MEMORY/MENU> area.
Thebuttonlights,andthe[AWB/ABB]menuappearsontheLCD
panel.
3. Turn the <F1> dial to select [VAR].
Colortemperatureconfigurationisenabledwhen[VAR]isselected,
anditisinitiallysettothecolortemperatureheldonthecamera.
Toadjustthesetting,proceedtothefollowing.
4. Press the <8 (CAMERA)> button in the <PRESET
MEMORY/MENU> area.
Thebuttonlights,andthe[GROUP]menuappearsontheLCDpanel.
5. Turn the <F1> dial to select [COLOR TEMP], then press
the <F1> dial.
Thecolortemperatureappearsonthebottomright(F2area)ofthe
LCDpanel.
6. Turn the <F2> dial to select the color temperature, then
press the <F2> dial.
40
Basic operations (continued)
41