To correct a mistake in the IP address, subnet mask,
or default gateway
Press MFN or MEN to move the cursor to the incorrect
number, and make the correction.
3.7 Wireless LAN settings
Important:
R When configuring wireless LAN settings, confirm
that the unit is located within operational range
of your wireless access point.
R Depending on the type of wireless access point,
select the appropriate way to connect the unit
and access point.
– Access point is WPS compatible (with a WPS
button)
– Access point is WPS compatible (without a
WPS button)
– Access point is not WPS compatible
R It is also possible to configure wireless LAN
settings when installing the driver regardless of
the type of wireless access point or whether there
is a WPS button (page 25).
R For wireless security settings, refer to the
operating instructions of your wireless router
and other wireless products, etc.
3.7.1 WPS compatible access point (with a
WPS button)
1 Press the WPS button on your wireless access point.
2 Press and hold MWPSN on the unit until the LED starts
blinking.
R Perform step 2 within 1 minute of performing step
1.
R The LED blinks while connecting. When the
connection is complete, the LED stops blinking
and turns on.
3.7.2 WPS compatible access point (without
a WPS button)
Important:
R Make sure the LAN mode setting is set to
“WIRELESS” beforehand (feature #580 on
page 90).
1 MMENUN A MBNM5NM8NM3N A MSETN
R The PIN code of the unit is displayed.
2 Register the PIN code to your wireless access point.
3 MSETN
R Perform step 3 within 1 minute of performing step
2.
R The LED blinks while connecting. When the
connection is complete, the LED stops blinking
and turns on.
R If the unit enters standby mode during the
process, repeat from step 1 (the PIN code will be
renewed).
3.7.3 WPS incompatible access point
Important:
R Make sure the LAN mode setting is set to
“WIRELESS” beforehand (feature #580 on
page 90).
R The following setting information for your
wireless access point is required:
– Network name (SSID)
– Network key (WEP / WPA key)
*1
– Connection type
– Network authentication type
– Data encryption type
*1
If your wireless access point is equipped with
several network keys, use only the first
network key (this unit is equipped with a
single network key).
R If your wireless access point is configured to not
show the network name (SSID), enter the network
name (SSID) manually (feature #585 on
page 24).
1 MMENUN A MBNM5NM8NM4N A MSETN
2 Press MCN or MDN repeatedly to display the desired
network name (SSID). A MSETN
R Depending on the settings for your wireless
access point, it may be necessary to select
WEP64 or WEP128. Select the desired item, and
then press MSETN.
3 Enter the network key using the dial keypad
(page 53). A MSETN
R Depending on the settings for your wireless
access point, this step can be omitted if
encryption is not used.
R The LED blinks while connecting. When the
connection is complete, the LED stops blinking
and turns on.
Setting up your wireless access point manually
1. MMENUN A MBNM5NM8NM5N A MSETN
2. Enter the network name (SSID). A MSETN
3. Press MCN or MDN repeatedly to display the desired
connection type. A MSETN
4. Press MCN or MDN repeatedly to display the desired
network authentication type. A MSETN
5. Press MCN or MDN repeatedly to display the desired
data encryption type. A MSETN
6. Enter the network key using the dial keypad
(page 53). A MSETN
R Depending on the settings for your wireless
access point, this step can be omitted if
encryption is not used.
24
3. Preparation
To Next Page
Loading...
