Paradox Magellan MG5050 User Manual

Magellan / Spectra SP 42
User Report Codes (Default = FF)
Clear Report Codes
Reset Report Codes
For reporting code format instructions, see page 40.
Refer to Decimal and Hexadecimal Values on page 47.
Section Arming
Disarming/Cancel
Alarm
Section Arming
Disarming/Cancel
Alarm
[471] S. Master: ____/____ ____/____ [487] User 17: ____/____ ____/____
[472] Master 1: ____/____ ____/____ [488] User 18: ____/____ ____/____
[473] Master 2: ____/____ ____/____ [489] User 19: ____/____ ____/____
[474] User 4: ____/____ ____/____ [490] User 20: ____/____ ____/____
[475] User 5: ____/____ ____/____ [491] User 21: ____/____ ____/____
[476] User 6: ____/____ ____/____ [492] User 22: ____/____ ____/____
[477] User 7: ____/____ ____/____ [493] User 23: ____/____ ____/____
[478] User 8: ____/____ ____/____ [494] User 24: ____/____ ____/____
[479] User 9: ____/____ ____/____ [495] User 25: ____/____ ____/____
[480] User 10: ____/____ ____/____ [496] User 26: ____/____ ____/____
[481] User 11: ____/____ ____/____ [497]: User 27: ____/____ ____/____
[482] User 12: ____/____ ____/____ [498] User 28: ____/____ ____/____
[483] User 13: ____/____ ____/____ [499] User 29: ____/____ ____/____
[484] User 14: ____/____ ____/____ [500] User 30: ____/____ ____/____
[485] User 15: ____/____ ____/____ [501] User 31: ____/____ ____/____
[486] User 16: ____/____ ____/____ [502] User 32: ____/____ ____/____
[966] Clear Report Codes
Option OFF ON
[1]
Clear zone report codes*
N Disabled N Enabled
[2]
Clear user report codes*
N Disabled N Enabled
[3]
Clear arm/disarm/alarm report codes*
N Disabled N Enabled
[4]
Clear trouble report codes*
N Disabled N Enabled
[5]
Clear system special report codes*
N Disabled N Enabled
[6]
Clear report code for GSM lost communication with panel*
N Disabled N Enabled
* Enable all options you want to clear. The respective sets of report codes will be cleared after exiting the section.
[967] Reset Report Codes
Option OFF ON
[1]
Reset zone report codes to default**
N Disabled N Enabled
[2]
Reset user report codes to default**
N Disabled N Enabled
[3]
Reset arm/disarm/alarm report codes to default**
N Disabled N Enabled
[4]
Reset trouble report codes to default**
N Disabled N Enabled
[5]
Reset system special report codes to default**
N Disabled N Enabled
[6]
Reset report code for GSM lost communication with panel**
N Disabled N Enabled
** Enable all options you want to reset to default. The respective sets of report codes will be reset to default after exiting the
section.

Paradox Magellan MG5050 Specifications

General

Partitions	2
User Codes	32
Event Buffer	256
Built-in Transceiver	Yes
Remote Control	Yes
Wireless Keypads	Yes
StayD Mode	Yes
Remotes	Up to 32
Power Supply	16.5 VAC
Zones	32
Battery Backup	7Ah