peplink 20 - Page 143

To Next Page

To Previous Page

USER MANUAL

Peplink Balance Series

The Inbound firewall settings are located at:Network > Firewall> Inbound Firewall Rule.

Once you click on Add Rule the following window will appear.

Main Page

User Manual1
Table of Contents2
Introduction and Scope5
Glossary6
Product Comparison Chart7
Product Features11
Supported Network Features11
Other Supported Features12
Package Contents14
Peplink Balance 20 / 3014
Peplink Balance 210 / 31014
Peplink Balance305 / 380 / 580 / 710 / 1350 / 250014
Peplink Balance Overview15
Peplink Balance 2015
Peplink Balance 3017
Peplink Balance 21019
Peplink Balance 31021
Peplink Balance 30523
Peplink Balance 38026
Peplink Balance 58029
Peplink Balance 71032
Peplink Balance 135035
Peplink Balance 250038
Installation42
Preparation42
Constructing the Network42
Configuring the Network Environment44
Basic Configuration45
Connecting to Web Admin Interface45
Configuration with Setup Wizard46
Advanced Setup48
Configuration of Lan Interface50
Drop-In Mode54
Configuration of Wan Interface57
Connection Method(S)59
Static Ip Connection60
Pppoe Connection61
Physical Interface Settings65
WAN Health Check67
Bandwidth Allowance Monitor70
Additional Public IP Settings71
Dynamic DNS Settings72
Bandwidth Bonding Speedfusion74
Speedfusion TM Settings74
Peplink Balance Behind NAT Router79
Speedfusion TM Status80
Ipsec Vpn81
Ipsec VPN Settings81
Ipsec Status84
Management of Outbound Traffic to Wan84
Outbound Policy84
Custom Rules for Outbound Policy86
Inbound Access92
Definition of Port Forwarding92
Definition of Servers on LAN94
Inbound Access Services95
Reverse Lookup Zones109
DNS Record Import Wizard112
Nat Mappings115
Wlan Controller117
WLAN Information117
AP Management122
Wireless Networks123
Static Wep125
Captive Portal Management128
AP Profile135
Qos138
User Groups138
Bandwidth Control139
Application140
Firewall142
Outbound and Inbound Firewall Rules142
Web Blocking149
Miscellaneous Settings150
High Availability150
PPTP Server153
Service Forwarding155
Service Passthrough157
System Settings158
Admin Security158
Firmware Upgrade162
Time163
Email Notification164
Remote Syslog166
Snmp167
Incontrol169
Configuration170
Reboot171
Tools171
Ping Test171
Traceroute Test173
Speedfusion173
Speedfusion TM Test173
CLI (Command Line Interface Support)174
Status175
Device175
Active Sessions176
Client List178
Access Point179
WINS Client179
Speedfusion179
Speedfusion TM Status179
Event Log180
Bandwidth181
Appendix A. Restoration of Factory Defaults186
Appendix B. Routing under Dhcp, Static Ip, and Pppoe187
Routing Via Network Address Translation (NAT)187
Routing Via IP Forwarding188
Appendix C. Case Studies189
Performance Optimization189
C.1 Performance Optimization189
Maintaining the same IP Address Throughout a Session191
Bypassing the Firewall to Access Hosts on LAN192
Inbound Access Restriction193
Outbound Access Restriction194
Appendix D. Troubleshooting195
Appendix E. Product Specifications197
Peplink Balance 20 and 30197
Peplink Balance 210 and 310198
E.2 Peplink Balance 210 and 310198
Peplink Balance 380199
Peplink Balance 305200
Peplink Balance 380201
Peplink Balance 580202
Peplink Balance 710203
Peplink Balance 1350204
Peplink Balance 2500205
Appendix F. Declaration206

peplink 20 - Page 143

Table of Contents

Related product manuals