To playback all discs on the disc trays
● Press PLAYÉ (ÉÅ).
➜ All the available discs will playback once, then
stop.
➜ During playback, the selected disc tray, track
number and elapsed playing time of the current
track will appear on the display.
To playback one disc only
● Press one of the CD DIRECT 1/2/3 buttons
on the remote control.
➜ The selected disc will playback once, then
stop.
To interrupt playback
● Press PAUSEÅ(ÉÅ).
➜ The current track time flashing.
● To resume playback, press PLAYÉ(ÉÅ)
again.
To stop playback
● Press Ç.
To search for a particular passage during
playback
● Press and hold à or á and release it when
the desired passage is located.
➜ During searching, the volume will be reduced.
To select a desired track
● Press í or ë repeatedly until the desired
track appears on the display.
● If playback is stopped, press PLAYÉ(ÉÅ) to
start playback.
Note:
– In Shuffle mode, pressing
í
will cause the
player to skip only to the beginning of the current
track.
To skip to the beginning of the current
track during playback
● Press í once.
To replace disc during playback
You are able to replace or load in disc into the
other two disc trays without interrupting current
playback.
● While playback, press the disc OPEN•CLOSE
button of the inactive disc trays (refer to
“Loading Disc”).
● If you press disc OPEN•CLOSE button of the
active disc tray, the disc will stop playing and the
disc tray will slide out.
➜ Once the disc tray is opened, it will be
deselected.
Programming the disc tracks
Programming tracks is possible when playback is
stopped. Up to 40 tracks can be stored in the
memory in any order.
1
Load the desired discs on the disc trays (refer to
“Loading Disc”).
2
Press PROG to start programming.
➜
PROGRAM
will start flashing.
3
Press 3CDC or CD DIRECT 1/2/3 button to
select a disc.
4
Press í or ë repeatedly to select the desired
track.
5
Press PROG to store the track.
¶ Repeat steps 3–5 to store other discs and
tracks.
6
Press PLAYÉ(ÉÅ) to start programme
playback.
➜ "
PLAY PROGRAMPLAY PROGRAM
PLAY PROGRAMPLAY PROGRAM
PLAY PROGRAM" will be displayed.
● To end programming without starting playback,
press Ç once .
➜ The total number of tracks programmed and
the total playing time will appear on the display.
Notes:
– If the total playing time is more than "
99:59
"
or if one of the programmed tracks has a number
greater than 30, then "
--:--
" will appear on the
display instead of the total playing time.
– If you attempt to programme more than 40
tracks, "
PROGRAM FULL
" will be displayed.
– If you press any of the CD DIRECT 1/2/3
buttons on the remote control, the system will
playback the selected disc or track, and the stored
programme will be ignored temporarily. The
PROGRAM
symbol also will disappear temporarily
from the display. It will reappear when playback of
the selected disc ends.
18
English
– During programming, if no key is pressed within
20 seconds, the system will exit the Programme
mode automatically.
To review the programme
● Stop playback and press í or ë repeatedly.
● To exit review mode, press Ç.
To erase the entire programme
● Press Ç once when playback is stopped or
twice during playback.
➜ "
PROGRAM CLEAREDPROGRAM CLEARED
PROGRAM CLEAREDPROGRAM CLEARED
PROGRAM CLEARED" will be displayed.
➜
PROGRAM
will disappear from the display.
Note:
– The programme will be erased when the system
is disconnected from the power supply or when the
disc tray is opened.
Repeat
The current track, a disc, all available discs or all
programmed tracks can be played repeatedly.
1
Press REPEAT on the remote control
repeatedly to select various repeat modes.
● In normal playback
➜ "
TRACKTRACK
TRACKTRACK
TRACK" – to repeat the current track,
REPEAT
will appear on the display.
➜ "
DISCDISC
DISCDISC
DISC" – to repeat the entire disc,
REPEAT
and
DISC
will appear on the display.
➜ "
ALL DISCALL DISC
ALL DISCALL DISC
ALL DISC" – to repeat all available discs,
REPEAT
,
DISC
and
ALL
will appear on the display.
● In programme playback
➜ "
TRACKTRACK
TRACKTRACK
TRACK" – to repeat the current
programmed track,
REPEAT
and
PROGRAM
will
appear on the display.
➜ "
PROGRAMPROGRAM
PROGRAMPROGRAM
PROGRAM" – to repeat all programmed
tracks,
REPEAT
,
PROGRAM
,
DISC
and
ALL
will
appear on the display.
● The selected track/disc(s)/programme will now
be played repeatedly until you press Ç.
2
To resume normal playback, press REPEAT
until the "
OFFOFF
OFFOFF
OFF" mode is displayed.
➜
REPEAT
will disappear from the display.
Notes:
– Selecting SHUFFLE during repeat playback will
cancel all repeat modes.
–Pressing any disc OPEN•CLOSE button will
cancel all repeat modes.
CD Operation
Shuffle
All the available discs and their tracks or all the
programmed tracks can be played in random
order.
1
Press SHUFFLE on the remote control.
➜
SHUFFLE
will appear on the display.
● The discs and the tracks will be played in
random order until you press Ç.
2
To resume normal playback, press SHUFFLE
again.
➜
SHUFFLE
will disappear from the display.
When select REPEAT mode during
shuffling
● In normal shuffled playback
➜ "
TRACKTRACK
TRACKTRACK
TRACK" – to repeat shuffling the current
track.
➜ "
ALL DISCALL DISC
ALL DISCALL DISC
ALL DISC" – to repeat shuffling all
available discs.
● In programme shuffled playback
➜ "
TRACKTRACK
TRACKTRACK
TRACK" – to repeat shuffling the current
programmed track.
➜ "
PROGRAMPROGRAM
PROGRAMPROGRAM
PROGRAM" – to repeat shuffling all
programmed tracks.
Note:
–Pressing any disc OPEN•CLOSE button will
cancel shuffle mode.
For Recording, please refer to “Tape
Operation/Recording”.
To Next Page
Loading...
