25
English
Clock/Timer
IMPORTANT!
When in Eco Power Standby mode, it is not
possible to operate clock or timer function.
Clock Setting
The clock can be set in either 12-hour or
24-hour mode ("
AM 12:00AM 12:00
AM 12:00AM 12:00
AM 12:00" or "
00:0000:00
00:0000:00
00:00" for
example)
1
Press and hold CLOCK on the remote control
until the time flashing on the display.
2
Press PROG on the system repeatedly to select
clock mode.
➜ If 12-hour mode is selected, "
AM XX:XXAM XX:XX
AM XX:XXAM XX:XX
AM XX:XX"
will start flashing.
➜ If 24-hour mode is selected, "
XX:XXXX:XX
XX:XXXX:XX
XX:XX" will
start flashing.
3
Press à or á on the system repeatedly to set
the hour.
4
Press í or ë on the system repeatedly to set
the minute.
5
Press CLOCK again to store the setting.
➜ The clock will start working.
To exit without storing the setting
● Press Çon the system.
Notes:
– The clock setting will be cancelled when the
power cord is disconnected or if a power failure
occurs.
– During clock setting, if no key is pressed within
90 seconds, the system will exit clock setting mode
automatically.
–To set the clock automatically through the time
information in the RDS signal, refer to "Radio
Reception - RDS Time".
Display Clock
The system allows you to select clock display or
normal display in any source mode (except Eco
Power Standby mode). When in Standby mode,
the clock will automatically be displayed.
● Press CLOCK on the remote control
repeatedly to select clock display or normal
display mode.
➜ When in clock display mode, clock will be
displayed. If the clock has not been set, "
--:----:--
--:----:--
--:--"
will appear on the display.
Note:
– If you pressed any keys during clock display
mode, the display will briefly show the information
related to the selected mode.
26
English
Timer Setting
The system can switch on to CD, TUNER, or
TAPE mode automatically at a preset time,
serving as an alarm to wake you up.
IMPORTANT!
– Before setting the timer, ensure that the
clock is set correctly.
– The timer will always be switched on
after it has been set.
– The timer will not start if a recording is in
progress.
– The volume of the timer will increase
gradually from the minimum level until it
reaches the last tuned volume level.
1
Press and hold TIMER on the remote control
for more than two seconds.
➜ "
AM 12:00AM 12:00
AM 12:00AM 12:00
AM 12:00" or "
00:0000:00
00:0000:00
00:00" or the last timer
setting will start flashing.
➜
TIMER
will start flashing.
➜ The selected source will be lighted while
other available sources are flashing.
2
Press 3CDC, TUNER or TAPE to select the
desired source.
● Before setting timer, make sure the music source
has been prepared.
3CDC – Load the disc(s). To start from a
specific track, make a programme (refer to “CD
Operation - Programming the disc tracks”).
TUNER – tune to the desired radio station.
TAPE – load a prerecorded tape.
3
Press à or á on the system repeatedly to set
the hour for the timer to start.
4
Press í or ë on the system repeatedly to set
the minute for the timer to start.
5
Press TIMER to store the start time.
➜ "
TIMER ONTIMER ON
TIMER ONTIMER ON
TIMER ON" will be displayed and followed
by the set timer "
XX:XXXX:XX
XX:XXXX:XX
XX:XX" and then the selected
source.
➜
TIMER
will remain on the display.
● At the preset time, the selected source will play.
To exit without storing the setting
● Press Çon the system.
Notes:
– If the selected source (CD) is not available when
preset timer is reached, TUNER will be selected
automatically.
– During timer setting, if no key is pressed within
90 seconds, the system will exit timer setting mode
automatically.
To check the TIMER
● Press TIMER on the remote control.
➜ If the timer has been activated, the set timer
information will be displayed.
➜ If the timer has been deactivated, "
OFFOFF
OFFOFF
OFF" will
be displayed.
To activate/deactivate the TIMER
● Press TIMER ON/OFF repeatedly on the
remote control.
➜ If activated, the last set timer information will
be shown for a few seconds and
TIMER
will
appear on the display.
➜ If deactivated, “
OFFOFF
OFFOFF
OFF” will be displayed.
Sleep Timer Setting
The sleep timer enables the system to switch to
Standby mode automatically at a preset time.
1
Press SLEEP on the remote control repeatedly
to select a preset time.
➜ The selections are as follows (time in
minutes):
1515
1515
15
™™
™™
™
3030
3030
30
™™
™™
™
4545
4545
45
™™
™™
™
6060
6060
60
™™
™™
™
OFFOFF
OFFOFF
OFF
™™
™™
™
1515
1515
15 …
➜ "
SLEEP XXSLEEP XX
SLEEP XXSLEEP XX
SLEEP XX" or "
OFFOFF
OFFOFF
OFF" will be displayed.
"
XXXX
XXXX
XX" is the time in minutes.
2
When you reach the desired length of time, stop
pressing the SLEEP button.
➜
SLEEP
will appear on the display, except for
"
OFFOFF
OFFOFF
OFF" mode.
➜ The Sleep Timer is now set. Before the
system switches to standby mode, a countdown
of 10 seconds will be displayed.
"
SLEEP 10SLEEP 10
SLEEP 10SLEEP 10
SLEEP 10"
™™
™™
™ "
SLEEP 9SLEEP 9
SLEEP 9SLEEP 9
SLEEP 9"....
™™
™™
™
"
SLEEP 1SLEEP 1
SLEEP 1SLEEP 1
SLEEP 1"
™™
™™
™ "
SLEEPSLEEP
SLEEPSLEEP
SLEEP"
While SLEEP mode is activated
To check the remaining length of time
● Press SLEEP once.
To change the preset sleep timer
● Press SLEEP twice.
➜ The display will show the remaining time
followed by the sequence of sleep timer options.
To deactivate the Sleep Timer
● Press SLEEP repeatedly until "
OFFOFF
OFFOFF
OFF" is
displayed, or press the STANDBY ON button.
Clock/Timer
To Next Page
Loading...
