FRANÇAIS
39
10. '
Pièces nécessaires :
1 x Indicateur de chaleur (#5)
1 x Porte d’armoire (#9)
Installation :
• Retirez la rondelle et l'écrou papillon de l'indicateur de chaleur emballée.
• Insérez l'indicateur de chaleur dans le trou de montage à l'avant de la
porte de l'armoire, placez la rondelle sur le filetage à l'intérieur de la
porte et serrez à la main pour la fixer.
REMARQUE: L'indicateur est fournie avec une rondelle et un écrou
papillon.
11.
'
Pièces nécessaires :
1 x Joint du poignée de porte d’armoire (#6)
1 x Poignée de porte d’armoire (#7)
1 x Loquet de porte d'armoire (#8)
4 x Vis (#C)
Installation :
• Tout d'abord, remontez la porte sur l'armoire principale en alignant
et en fixant les deux charnières. Assurez-vous que la porte est
correctement montée en regardant si elle s'ouvre correctement.
• Montez la poignée de la porte de l'armoire sur le côté avant de la porte
à l'aide de deux vis. Vérifiez l'emplacement correct sur l'illustration 11.
• Montez le loquet de la porte de l'armoire sur le côté extérieur de
l'armoire principale à l'aide de deux vis. Illustration 11.
12.
Pièces nécessaires :
1 x Support de fixation de la bouteille à gaz (#18)
4 x Vis (#B)
Installation :
• Montez le support de fixation de la bouteille à gaz sur l'armoire
principale à l'aide de quatre vis comme indiqué sur l'illustration.
1
BRACKET INTO THE LOWER SMOKER
CABINET ASSEMBLY
Parts Required:
1 x Lower Smoker Cabinet Assembly (#14)
Installation:
(#17) to the Lower Smoker Cabinet
Fig.15
5.2 shown.
1
.
ASSEMBLY INTO THE LOWER
SMOKER CABINET ASSEMBLY
Parts Required:
1 x Wood Chip Box Lid (#11)
1 x Wood Chip Box Assembly (#12)
1 x Lower Smoker Cabinet Assembly (#14)
Installation:
•Put the Wood Chip Box Lid (#11) on
the Wood Chip Box Assembly (#12)
and slide Wood Chip Box onto the
Wood Chip Box support rails of Lower
Smoker Cabinet Assembly (#14) as
Fig.16 shown.
1
BRACKET INTO THE LOWER SMOKER
CABINET ASSEMBLY
Parts Required:
1 x Lower Smoker Cabinet Assembly (#14)
Installation:
(#17) to the Lower Smoker Cabinet
Fig.15
5.2 shown.
1
.
ASSEMBLY INTO THE LOWER
SMOKER CABINET ASSEMBLY
Parts Required:
1 x Wood Chip Box Lid (#11)
1 x Wood Chip Box Assembly (#12)
1 x Lower Smoker Cabinet Assembly (#14)
Installation:
•Put the Wood Chip Box Lid (#11) on
the Wood Chip Box Assembly (#12)
and slide Wood Chip Box onto the
Wood Chip Box support rails of Lower
Smoker Cabinet Assembly (#14) as
Fig.16 shown.
10
1
.
MOUNTING DOOR LATCH ASSEMBLY
TO THE UPPER SMOKER CABINET
ASSEMBLY
Parts Required:
2 x #10-24*1/2”(#C)
Installation:
(#2) using 2 x #10-24*1/2”(#C) as
Fig.1
shown.
12.
INSERTING HEAT INDICATOR INTO
THE DOOR ASSEMBLY
Parts Required:
1 x Door Assembly (#10)
1 X Heat
Installation:
•
the mounting hole in
by hand as Fig.12 shown.
1
.
MOUNTING DOOR HANDLE TO THE
DOOR ASSEMBLY
Parts Required:
1 x Door Handle (#7)
1 x Silicon Washer (#8)
1 X Door Assembly (#10)
2 x #10-24*1/2”(#C)
Installation:
• Attach the Door Handle (#7) with Silicon
Washer (#8) to the Door Assembly (#10)
using 2 x #10-24*1/2”(#C) as Fig.14
shown.
11
11
12
5
9
1
.
MOUNTING DOOR LATCH ASSEMBLY
TO THE UPPER SMOKER CABINET
ASSEMBLY
Parts Required:
2 x #10-24*1/2”(#C)
Installation:
(#2) using 2 x #10-24*1/2”(#C) as
Fig.1
shown.
12.
INSERTING HEAT INDICATOR INTO
THE DOOR ASSEMBLY
Parts Required:
1 x Door Assembly (#10)
1 X Heat
Installation:
•
the mounting hole in
by hand as Fig.12 shown.
1
.
MOUNTING DOOR HANDLE TO THE
DOOR ASSEMBLY
Parts Required:
1 x Door Handle (#7)
1 x Silicon Washer (#8)
1 X Door Assembly (#10)
2 x #10-24*1/2”(#C)
Installation:
• Attach the Door Handle (#7) with Silicon
Washer (#8) to the Door Assembly (#10)
using 2 x #10-24*1/2”(#C) as Fig.14
shown.
1
.
MOUNTING DOOR LATCH ASSEMBLY
TO THE UPPER SMOKER CABINET
ASSEMBLY
Parts Required:
2 x #10-24*1/2”(#C)
Installation:
(#2) using 2 x #10-24*1/2”(#C) as
Fig.1
shown.
12.
INSERTING HEAT INDICATOR INTO
THE DOOR ASSEMBLY
Parts Required:
1 x Door Assembly (#10)
1 X Heat
Installation:
•
the mounting hole in
by hand as Fig.12 shown.
1 .
MOUNTING DOOR HANDLE TO THE
DOOR ASSEMBLY
Parts Required:
1 x Door Handle (#7)
1 x Silicon Washer (#8)
1 X Door Assembly (#10)
2 x #10-24*1/2”(#C)
Installation:
• Attach the Door Handle (#7) with Silicon
Washer (#8) to the Door Assembly (#10)
using 2 x #10-24*1/2”(#C) as Fig.14
shown.
1
.
MOUNTING DOOR LATCH ASSEMBLY
TO THE UPPER SMOKER CABINET
ASSEMBLY
Parts Required:
2 x #10-24*1/2”(#C)
Installation:
(#2) using 2 x #10-24*1/2”(#C) as
Fig.1
shown.
12.
INSERTING HEAT INDICATOR INTO
THE DOOR ASSEMBLY
Parts Required:
1 x Door Assembly (#10)
1 X Heat
Installation:
•
the mounting hole in
by hand as Fig.12 shown.
1 .
MOUNTING DOOR HANDLE TO THE
DOOR ASSEMBLY
Parts Required:
1 x Door Handle (#7)
1 x Silicon Washer (#8)
1 X Door Assembly (#10)
2 x #10-24*1/2”(#C)
Installation:
• Attach the Door Handle (#7) with Silicon
Washer (#8) to the Door Assembly (#10)
using 2 x #10-24*1/2”(#C) as Fig.14
shown.
8
6
7
18
To Next Page
Loading...
