Record 6100 Series - Page 10

10
If a second Display Control
Panel has been connected,
this will set the contrast of
the second LCD display.
Note: The dip switch on the
back of the second display
SERVICE STG
Configure System >
Learning System >
Parameter >
Maintenance >
Functions >
SERVICE STG
Configure System >
Learning System >
Parameter >
Maintenance >
Functions >
Operation Mode >
SERVICE STG
Configure System >
Learning System >
Parameter >
Maintenance >
Functions >
SERVICE STG
Configure System >
Learning System >
Parameter >
Maintenance >
Functions >
Operation Mode >
PARAMETER
Driving cycle >
Time delay open >
Drive >
Entrance system >
Manual control >
Control panel >
CONTROL PANEL
Mechanical Panel 2
Display panel >
DISPLAY PANEL
Select language 3
Keyboard 1
Contrast BDE1 20
Contrast BDE2 20
Brightness BDE2 20
SELECT LANGUAGE
0 DEUTSCH
1 FRANCAIS
2 ENGLISH
3 ENGLISH US
Selects the language
Display Control Panel.
ESPANOL
NEDERLANDS
PARAMETER
Driving cycle >
Time delay open >
Drive >
Entrance system >
Manual control >
Control panel >
CONTROL PANEL
Mechanical Panel 2
Display panel >
DISPLAY PANEL
Select language 3
Keyboard 1
Contrast BDE1 20
Contrast BDE2 20
Brightness
KEYBOARD
0 Locked-Mode
1 OFF-Mode
If the electric locking is to
be active when the unit is
turned “OFF”, this should
be set to “0 Locked-Mode”.
When the “OFF” button on
the Display Control Panel is
pressed, a padlock will
appear on the display. If
the unit is turned off with
the On/Off/Open rocker
switch, “OFF” will appear on
the display.
Brightne
SERVICE STG
Configure System >
Learning System >
Parameter >
Maintenance >
Functions >
SERVICE STG
Configure System >
Learning System >
Parameter >
Maintenance >
Functions >
Operation Mode >
PARAMETER
Driving cycle >
Time delay open >
Drive >
Entrance system >
Manual control >
Control panel >
CONTROL PANEL
Mechanical Pannel 2
Display panel >
DISPLAY PANEL
Select language 3
Keyboard 1
Contrast BDE1 20
Contrast BDE2 20
Brightness
CONTRAST BDE1
20
If a Display Control Panel
has been connected, this
will set the contrast of the
LCD display.
Brightne
SERVICE STG
Configure System >
Learning System >
Parameter >
Maintenance >
Functions >
SERVICE STG
Configure System >
Learning System >
Parameter >
Maintenance >
Functions >
Operation Mode >
PARAMETER
Driving cycle >
Time delay open >
Drive >
Entrance system >
Manual control >
Control panel >
CONTROL PANEL
Mechanical Panel 2
Display panel >
DISPLAY PANEL
Select language 3
Keyboard 1
Contrast BDE1 20
Contrast BDE2 20
Brightne
CONTRAST BDE2
20
must be set to “BDE2”.
Brightne
displayed on the optional
SERVICE STG
Configure System >
Learning System >
Parameter >
Maintenance >
Functions >
SERVICE STG
Configure System >
Learning System >
Parameter >
Maintenance >
Functions >
Operation Mode >
PARAMETER
Driving cycle >
Time delay open >
Drive >
Entrance system >
Manual control >
Control panel >
CONTROL PANEL
Mechanical Panel 2
Display panel >
MECHANICAL PANEL
0 3 Pos. (AUTO)
1 4 Positions (VDAH)
2 3 Pos. (OFF-A)
8 3 Pos. (OFF-M)
9 3 Pos. (Lock-A)
10 3 Pos. (Lock-M)
3 Pos.(AUTO) is used on units when
no rocker switch is connected.
3 Pos.(OFF-M) is the normal setting.
3 Pos.(Lock-M) is used when a lock is
present and the door is to be locked
when turned OFF.
when power hold closed is desired.
3 Pos. (OFF-A) and (Lock-A) are used
4 Pos.(VDAH) not used in the US.
keyswitch or BDE-D Display module
4 Pos.(VDAE) is used with a BDE-M.
to support; AUTO, ONE-WAY, CONT.
OPEN and LOCKED.
MECHANICAL PANEL
14 4 Pos. (VDAE)
1 4 Positions (VDAH)
2 3 Pos. (OFF-A)
8 3 Pos. (OFF-M)
9 3 Pos. (Lock-A)
10 3 Pos. (Lock-M)
Brightness BDE2 20