❍Effect 1 (Reverb Send Level)
STATUS SECOND THIRD
BnH 5BH vvH
n=MIDI Channel Number :0H - FH (0 - 15) 0=ch.1 15=ch.16
vv=Control Value :00H - 7FH (0 - 127)
* Can be received only through the Basic channel.
●Program Change
STATUS SECOND
CnH ppH
n=MIDI Channel Number :0H - FH (0 - 15) 0=ch.1 15=ch.16
pp=Program Number :00H - 7FH (0 - 127) 0=Prg.1 127=Prg.128
* Can be received only through the Basic channel.
* The recognized Program Change number corresponds to each patch as follows,
<When the patches of group A, B, C or D are selected...>
1... 4 = A11...A14 65...68 = C11...C14
5... 8 = A21...A24 69...72 = C21...C24
9...12 = A31...A34 73...76 = C31...C34
13...16 = A41...A44 77...80 = C41...C44
17...20 = A51...A54 81...84 = C51...C54
21...24 = A61...A64 85...88 = C61...C64
25...28 = A71...A74 89...92 = C71...C74
29...32 = A81...A84 93...96 = C81...C84
33...36 = b11...b14 97...100 = d11...d24
37...40 = b21...b24 101...104 = d21...d24
41...44 = b31...b34 105...108 = d31...d34
45...48 = b41...b44 109...112 = d41...d44
49...52 = b51...b54 113...116 = d51...d54
53...56 = b61...b64 117...120 = d61...d64
57...60 = b71...b74 121...124 = d71...d74
61...64 = b81...b84 125...128 = d81...d84
* When you call the patches of the Group E,F,G or H, send the value “1” of the controller
number 0 before the program change message sending.
<When the patches of group E, F, G or H are selected...>
1... 4 = E11...E14 65...68 = G11...G14
5... 8 = E21...E24 69...72 = G21...G24
9...12 = E31...E34 73...76 = G31...G34
13...16 = E41...E44 77...80 = G41...G44
17...20 = E51...E54 81...84 = G51...G54
21...24 = E61...E64 85...88 = G61...G64
25...28 = E71...E74 89...92 = G71...G74
29...32 = E81...E84 93...96 = G81...G84
33...36 = F11...F14 97...100 = H11...H24
37...40 = F21...F24 101...104 = H21...H24
41...44 = F31...F34 105...108 = H31...H34
45...48 = F41...F44 109...112 = H41...H44
49...52 = F51...F54 113...116 = H51...H54
53...56 = F61...F64 117...120 = H61...H64
57...60 = F71...F74 121...124 = H71...H74
61...64 = F81...F84 125...128 = H81...H84
* When you call the patches of the Group A,B,C or D, send the value “0” of the con-
troller number 0 before the program change message sending.
●Pitch Bend Change
STATUS SECOND THIRD
EnH llH mmH
n=MIDI Channel Number :0H - FH (0 - 15) 0=ch.1 15=ch.16
mm,ll=Value :00H,00H - 7FH,7FH (-8192 - +8191)
■Channel Mode Message
●All Note Off
STATUS SECOND THIRD
BnH 7BH 00H
n=MIDI Channel Number :0H - FH (0 - 15) 0=ch.1 15=ch.16
* Can be received only through the Basic channel.
* Turn off all notes that are now on .
●OMNI OFF
STATUS SECOND THIRD
BnH 7CH 00H
n=MIDI Channel Number :0H - FH (0 - 15) 0=ch.1 15=ch.16
* Can be received only through the Basic channel.
* Will act the same as All Note Off.
●OMNI ON
STATUS SECOND THIRD
BnH 7DH 00H
n=MIDI Channel Number :0H - FH (0 - 15) 0=ch.1 15=ch.16
* Can be received only through the Basic channel.
* Will act the same as All Note Off
●MONO
STATUS SECOND THIRD
BnH 7EH mmH
n=MIDI Channel Number :0H - FH (0 - 15) 0=ch.1 15=ch.16
mm=Number of Individual Channels :ignored
* Can be received only through the Basic channel.
* Will act the same as All Note Off
●POLY
STATUS SECOND THIRD
BnH 7FH 00H
n=MIDI Channel Number :0H - FH (0 - 15) 0=ch.1 15=ch.16
* Can be received only through the Basic channel.
* Will act the same as All Note Off.
■System Realtime Message
●Active Sensing
STATUS
FEH
* Having received this massage, GR-30 expects to receive information of any status of
data during about 420msec. If GR-30 doesn’t receive any massage during that time, it
acts as if the All Note Off massage is received, and returns to normal operation (will
not check interval of massages).
●Timing Clock
STATUS
F8H
* Can be received only when the A-TEMPO is set to “Syn”.
●Start
STATUS
FAH
* Can be received only when the A-TEMPO is set to “Syn” and the realtime recording of
arpeggiater is ready.
●Continue
STATUS
FBH
* Can be received only when the A-TEMPO is set to “Syn” and the realtime recording of
arpeggiater is ready
●Stop
STATUS
FCH
* Can be received only when the A-TEMPO is set to “Syn” and the realtime recording of
arpeggiater is ready
■System Exclusive Message
STATUS DATA BYTES
F0H iiH ddH ............eeH
F7H
F0H :System Exclusive
ii = Manufacturer ID :41H ( 65 )
dd ......ee = Data : 00H - 7FH ( 0 - 127 )
F7H : EOX (End of Exclusive)
* Refer to Section 3, 4, and the pages of “Roland Exclusive Message” for more detailed
information.
93
12
To Next Page
Loading...
Need help?
General
