Roland TAIKO-1 - Page 47

Appendix
47
CHORUS
This is a stereo chorus. A lter is provided so that you can adjust the
timbre of the chorus sound.
Parameter Value Explanation
Filter Type OFF, LPF, HPF
Filter type
OFF: Filter is not used
LPF: High frequencies at or above the cuto
value are ltered
HPF: Low frequencies at or below the cuto
value are ltered
Cuto Freq 200–8000 [Hz]
Center frequency at which the lter cuts a
specic frequency region
Pre Delay 0.0–100.0 [ms]
Delay time from the direct sound until the
chorus sound is heard
Tempo Sync Sw OFF, ON
Sets whether the modulation rate is specied
as a note value (ON) or not (OFF).
Rate
0.05–10.00 [Hz],
note
Rate of modulation
Depth 0–127 Depth of modulation
Phase 0–180 [deg] Spatial spread (depth) of the chorus sound
Low Gain -15–+15 [dB] Amount of low range boost/cut
High Gain -15–+15 [dB] Amount of high range boost/cut
Level 0–127 Output level
SPACE-D
This is a multiple chorus that applies two-phase modulation in stereo.
It gives no impression of modulation, but produces a transparent
chorus eect.
Parameter Value Explanation
Pre Delay 0.0–100.0 [ms]
Delay time from the direct sound until the
chorus sound is heard
Tempo Sync OFF, ON
Sets whether the modulation rate is specied
as a note value (ON) or not (OFF).
Rate
0.05–10.00 [Hz],
note
Rate of modulation
Depth 0–127 Depth of modulation
Phase 0–180 [deg] Spatial spread (depth) of the chorus sound
Low Gain -15–+15 [dB] Amount of low range boost/cut
High Gain -15–+15 [dB] Amount of high range boost/cut
Level 0–127 Output level
OD
0
CHORUS
Parameter Value Explanation
Overdrive Drive 0–127
The degree of distortion.
Also changes the volume.
Overdrive Pan L64–R63 Stereo position of the overdrive sound
Chorus Pre Delay 0.0–100.0 [ms]
Delay time from the direct sound until the
chorus sound is heard
Tempo Sync Sw OFF, ON
Sets whether the modulation rate is specied
as a note value (ON) or not (OFF).
Rate
0.05–10.00 [Hz],
note
Rate of modulation
Chorus Depth 0–127 Depth of modulation
Chorus Balance
D100:0W–
D0:100W
Volume balance between the sound that is
sent through the chorus (W) and the sound
that is not sent through the chorus (D).
Level 0–127 Output level
DS
0
CHORUS
The parameters are essentially the same as in “OD
0
CHORUS” with
the exception of the following two.
Overdrive Drive
0
Distortion Drive, Overdrive Pan
0
Distortion Pan
PHASER 1
This is a stereo phaser. The phase of the original sound is shifted to
modulate the overall sound.
Parameter Value Explanation
Mode
4-STAGE,
8-STAGE, 12-STAGE
Number of stages in the phaser
Manual 0–127
Center frequency from which the sound is
modulated
Tempo Sync Sw OFF, ON
Sets whether the modulation rate is specied
as a note value (ON) or not (OFF).
Rate
0.05–10.00 [Hz],
note
Frequency of modulation
Depth 0–127 Depth of modulation
Polarity
INVERSE,
SYNCHRO
This sets the left/right modulation phase.
INVERSE: left/right phases inverted
When using a mono source, this gives the
sound a more spread-out feel.
SYNCHRO: left/right phases synchronized
Select this when using a stereo source.
Resonance 0–127 Amount of feedback
Cross Feedback -98–+98 [%]
Adjusts the proportion of the phaser sound
that is fed back into the eect. (Negative values
invert the phase.)
Low Gain -15–+15 [dB] Amount of low range boost/cut
High Gain -15–+15 [dB] Amount of high range boost/cut
Level 0–127 Output level
PHASER 3
This simulates a dierent analog phaser than the Phaser 1 eect.
Parameter Value Explanation
Speed 0–100 Frequency of modulation
Depth 0–127 Depth of modulation
Low Gain -15–+15 [dB] Amount of low range boost/cut
High Gain -15–+15 [dB] Amount of high range boost/cut
Level 0–127 Output level