Roland TAIKO-1 - MIDI-Related Settings; (Global MIDI); Configuring the Master Equalizer; (Master EQ)

Making Overall Settings for the TAIKO-1 (Others)
38
MIDI-Related Settings (Global MIDI)
1. On the OTHERS screen, select “Global MIDI” and press
“SELECT” (F2 button).
The GLOBAL MIDI screen appears.
2. Use the [
H
] [
I
] buttons to select the item, and then
use the [+] [-] buttons to change the setting.
Parameter
[
H
] [
I
] buttons
Value
[+] [-] buttons
Explanation
MIDI Tx/Rx Sw OFF, ON
Turns the transmitting/receiving of MIDI
messages on/o.
MIDI Channel CH1–16 Sets the transmit/receive channel.
PAD1 Pos CC
OFF, 1, 2, 4, 11, 16,
17, 18, 19
Sets the controller number used for
transmitting/receiving the strike point of
pad 1.
PAD2 Pos CC
Sets the controller number used for
transmitting/receiving the strike point of
pad 2.
Pitch Ctrl CC
When the Pedal setting is “Pitch,” this
sets the controller number used for
transmitting/receiving the expression pedal
depth values (how deeply you press the
pedal).
HI-Reso Velocity OFF, ON
Sets CC#88 (high resolution velocity prex)
to enabled (ON) or disabled (OFF).
If this is disabled, the maximum velocities
supported by this instrument are limited
to 127.
Prog Change Tx OFF, ON
Sets whether program change messages
are sent (on/o).
Prog Change Rx OFF, ON
Sets whether program change messages
are received (on/o).
Local Control OFF, ON
Sets whether to transmit the performance
data from the pads to the sound module
of this instrument (ON to transmit, OFF to
disable).
This should normally be set to “ON.” When
this is “OFF,” the performance data from
the pads is disconnected from the sound
module.
3. Press the F1 button several times to return to the top
screen.
Conguring the Master Equalizer (Master EQ)
A four-band compressor is provided for each kit.
You can adjust the equalizer’s eect (shelving and peaking) for the low
frequencies (LOW) and high frequencies (HIGH).
The sound to which master EQ is applied is output from the OUTPUT
jack and PHONES jack.
5 You can use four bands (LOW/MID1/MID2/HIGH) of boost/cut to adjust the sound.
5 This is also useful for compensating for sound quality issues when using the
master compressor.
1. On the OTHERS screen, select “Master EQ” and press
“SELECT” (F2 button).
The MASTER EQ screen appears.
2. Use the [
H
] [
I
] buttons to select the item, and then
use the [+] [-] buttons to change the setting.
Parameter
[
H
] [
I
] buttons
Value
[+] [-] buttons
Explanation
EQ Sw OFF, ON Turns the master EQ on/o.
Low Type
SHELV
(Shelving),
PEAK
Selects how the equalizer eect works.
Low Freq 20–1k [Hz] Sets the center frequency.
Low Q
0.5–8.0
(only when Type is set to
“PEAK”)
Sets the bandwidth of the frequency region.
Higher values make the bandwidth
narrower.
Low Gain -12–+12 [dB]
Sets the amount of boost/cut for the low-
frequency region.
Mid1 Freq 20–16k [Hz] Sets the center frequency.
Mid1 Q 0.5–8.0
Sets the bandwidth of the frequency region.
Higher values make the bandwidth
narrower.
Mid1 Gain -12–+12 [dB] Sets the amount of boost/cut for Mid1.
Mid2 Freq 20–16k [Hz] Sets the center frequency.
Mid2 Q 0.5–8.0
Sets the bandwidth of the frequency region.
Higher values make the bandwidth
narrower.
Mid2 Gain -12–+12 [dB] Sets the amount of boost/cut for Mid2.
High Type
SHELV
(Shelving),
PEAK
Selects how the equalizer eect works.
High Freq 1k–16k [dB] Sets the center frequency.
High Q
0.5–8.0
(only when Type is set to
“PEAK”)
Sets the bandwidth of the frequency region.
Higher values make the bandwidth
narrower.
High Gain -12–+12 [dB]
Sets the amount of boost/cut for the high-
frequency region.
3. Press the F1 button several times to return to the top
screen.