Roland V-Drums TD-50 - Od 0 Delay; Ds 0 Delay; Chorus; Space-D

36
Multi-Eect Parameters
OD
0
DELAY
Parameter Value Explanation
Overdrive Drive 0–127
Degree of distortion
Also changes the volume.
Overdrive Pan L64–63R
Stereo location of the overdrive
sound
Tempo Sync OFF, ON
Species whether the delay time
value of the delay is specied as a
note value (ON) or not (OFF).
Delay Time 1–2600 ms, note
Adjusts the delay time from the
direct sound until the delay sound
is heard.
Delay Feedback -98–+98 %
Adjusts the proportion of the delay
sound that is fed back into the eect.
Negative “-” settings will invert the
phase.
Delay HF Damp
200–8000 Hz,
BYPASS
Adjusts the frequency above which
sound fed back to the eect will be
cut. If you do not want to cut the
high frequencies, set this parameter
to BYPASS.
Delay Balance
D100:0W–
D0:100W
Adjusts the volume balance between
the sound that is sent through the
delay (W) and the sound that is not
sent through the delay (D).
Level 0–127 Output Level
DS
0
DELAY
The parameters are essentially the same as in “OD
0
DELAY” with
the exception of the following two.
Overdrive Drive
0
Distortion Drive, Overdrive Pan
0
Distortion Pan
CHORUS
This is a stereo chorus. A lter is provided so that you can adjust the
timbre of the chorus sound.
Parameter Value Explanation
Filter Type OFF, LPF, HPF
Type of lter
OFF: no lter is used
LPF: cuts the frequency range above
the Cuto Freq
HPF: cuts the frequency range below
the Cuto Freq
Cuto Freq 200–8000 Hz Basic frequency of the lter
Pre Delay 0.0–100.0 ms
Adjusts the delay time from the
direct sound until the chorus sound
is heard.
Tempo Sync OFF, ON
Species whether the modulation
rate is specied as a note value (ON)
or not (OFF).
Rate
0.05–10.00 Hz,
note
Frequency of modulation
Depth 0–127 Depth of modulation
Phase 0–180 deg Spatial spread of the sound
Low Gain -15–+15 dB Gain of the low range
High Gain -15–+15 dB Gain of the high range
Level 0–127 Output Level
SPACE-D
This is a multiple chorus that applies two-phase modulation in
stereo. It gives no impression of modulation, but produces a
transparent chorus eect.
Parameter Value Explanation
Pre Delay 0.0–100.0 ms
Adjusts the delay time from the
direct sound until the chorus sound
is heard.
Tempo Sync OFF, ON
Species whether the modulation
rate is specied as a note value (ON)
or not (OFF).
Rate
0.05–10.00 Hz,
note
Frequency of modulation
Depth 0–127 Depth of modulation
Phase 0–180 deg Spatial spread of the sound
Low Gain -15–+15 dB Gain of the low range
High Gain -15–+15 dB Gain of the high range
Level 0–127 Output Level
OD
0
CHORUS
Parameter Value Explanation
Overdrive Drive 0–127
Degree of distortion
Also changes the volume.
Overdrive Pan L64–63R
Stereo location of the overdrive
sound
Chorus Pre Delay 0.0–100.0 ms
Adjusts the delay time from the
direct sound until the chorus sound
is heard.
Tempo Sync OFF, ON
Species whether the modulation
rate is specied as a note value (ON)
or not (OFF).
Rate
0.05–10.00 Hz,
note
Frequency of modulation
Chorus Depth 0–127 Depth of modulation
Chorus Balance
D100:0W–
D0:100W
Adjusts the volume balance between
the sound that is sent through the
chorus (W) and the sound that is not
sent through the chorus (D).
Level 0–127 Output Level
DS
0
CHORUS
The parameters are essentially the same as in “OD
0
CHORUS” with
the exception of the following two.
Overdrive Drive
0
Distortion Drive, Overdrive Pan
0
Distortion Pan