Roland V-Drums TD-50 - Phaser a; Phaser B; Step Phaser; Flanger

37
Multi-Eect Parameters
PHASER A
A phase-shifted sound is added to the original sound and
modulated.
Parameter Value Explanation
Mode
4-STAGE, 8-STAGE,
12-STAGE
Number of stages in the phaser
Manual 0–127
Adjusts the basic frequency from
which the sound will be modulated.
Tempo Sync OFF, ON
Species whether the modulation
rate is specied as a note value (ON)
or not (OFF).
Rate
0.05–10.00 Hz,
note
Frequency of modulation
Depth 0–127 Depth of modulation
Polarity
INVERSE,
SYNCHRO
Selects whether the left and right
phase of the modulation will be the
same or the opposite.
INVERSE: The left and right phase
will be opposite. When using a mono
source, this spreads the sound.
SYNCHRO: The left and right phase
will be the same. Select this when
inputting a stereo source.
Resonance 0–127 Amount of feedback
Cross Feedback -98–+98 %
Adjusts the proportion of the phaser
sound that is fed back into the eect.
Negative “-” settings will invert the
phase.
Low Gain -15–+15 dB Gain of the low range
High Gain -15–+15 dB Gain of the high range
Level 0–127 Output Level
PHASER B
This simulates a dierent analog phaser than Phaser A.
Parameter Value Explanation
Speed 0–100 Frequency of modulation
Depth 0–127 Depth of modulation
Low Gain -15–+15 dB Gain of the low range
High Gain -15–+15 dB Gain of the high range
Level 0–127 Output Level
STEP PHASER
The phaser eect will be varied gradually.
Parameter Value Explanation
Mode
4-STAGE, 8-STAGE,
12-STAGE
Number of stages in the phaser
Manual 0–127
Adjusts the basic frequency from
which the sound will be modulated.
Tempo Sync
(Rate)
OFF, ON
Species whether the modulation
rate is specied as a note value (ON)
or not (OFF).
Rate
0.05–10.00 Hz,
note
Frequency of modulation
Depth 0–127 Depth of modulation
Polarity
INVERSE,
SYNCHRO
Selects whether the left and right
phase of the modulation will be the
same or the opposite.
INVERSE: The left and right phase
will be opposite. When using a mono
source, this spreads the sound.
SYNCHRO: The left and right phase
will be the same. Select this when
inputting a stereo source.
Resonance 0–127 Amount of feedback
Cross Feedback -98–+98 %
Adjusts the proportion of the phaser
sound that is fed back into the eect.
Negative “-” settings will invert the
phase.
Tempo Sync
(Step Rate)
OFF, ON
Species whether the modulation
rate of the phaser eect is specied
as a note value (ON) or not (OFF).
Step Rate
0.10–20.00 Hz,
note
Rate of the step-wise change in the
phaser eect
Low Gain -15–+15 dB Gain of the low range
High Gain -15–+15 dB Gain of the high range
Level 0–127 Output Level
FLANGER
This is a stereo anger. (The LFO has the same phase for left and
right.) It produces a metallic resonance that rises and falls like a jet
airplane taking o or landing. A lter is provided so that you can
adjust the timbre of the anged sound.
Parameter Value Explanation
Filter Type OFF, LPF, HPF
Type of lter
OFF: no lter is used
LPF: cuts the frequency range above
the Cuto Freq
HPF: cuts the frequency range below
the Cuto Freq
Cuto Freq 200–8000 Hz Basic frequency of the lter
Pre Delay 0.0–100.0 ms
Adjusts the delay time from when the
direct sound begins until the anger
sound is heard.
Tempo Sync OFF, ON
Species whether the modulation
rate is specied as a note value (ON)
or not (OFF).
Rate
0.05–10.00 Hz,
note
Frequency of modulation
Depth 0–127 Depth of modulation
Phase 0–180 deg Spatial spread of the sound
Feedback -98–+98 %
Adjusts the proportion of the anger
sound that is fed back into the eect.
Negative “-” settings will invert the
phase.
Low Gain -15–+15 dB Gain of the low range
High Gain -15–+15 dB Gain of the high range
Level 0–127 Output Level