Need help?Do you have a question about the Rosenbauer FLF 15000 PANTHER and is the answer not in the manual?
General| Engine Power | 522 kW (700 hp) |
|---|---|
| Foam Tank Capacity | 1, 500 liters |
| Length | 10.5 meters |
| Width | 2.55 meters |
| Height | 3.6 meters |
| Weight | 32, 000 kg |
| Water Tank Capacity | 15, 000 liters |
Contact details for Rosenbauer International Aktiengesellschaft.
How to identify the vehicle's works order number.
Explains standard signs used in the manual for optional equipment.
Details various warning signs indicating potential hazards and their meanings.
Lists signs that indicate prohibited actions.
Lists signs indicating required safety equipment or actions.
Provides technical specifications for the vehicle chassis.
Details the capacity, material, and connections of the water tank.
Details the capacity, material, and location of the foam compound tank.
Specifies the pump manufacturer, type, performance, and connections.
Details the specifications and ratio of the pump gearbox.
Describes the manufacturer, material, and operation of the priming pump.
Explains the electronic foam proportioning system, its range, and rates.
Details the roof turret's manufacturer, type, performance, and control.
Lists the number, performance, and range of undertruck nozzles.
Details the bumper turret's manufacturer, type, performance, and control.
Describes the twin agent rapid intervention system and its specifications.
Details the dry powder unit's manufacturer, type, and components.
Describes the deluge system, its pump, and nozzles.
Details the light mast's manufacturer, location, and control.
Explains the basic principles and components of the pump.
Provides detailed description of the N 100 pump and its construction.
Explains how the pump is driven and the function of the gearbox.
Details the priming system's operation and components.
Explains how maximum lift is measured and factors affecting it.
Provides a detailed diagram of the piston priming pump.
Explains the system's advantages, working principle, range, and rates.
Describes the system that prevents pump overheating and its counteractions.
Explains the LCS Logic Control System and its CAN Bus architecture.
Details the Bostrom brackets for breathing apparatus, including opening and closing procedures.
Describes the Comfort 2002 brackets for breathing apparatus, including operation and safety.
Lists and describes switches and pilot lamps on the right, left, and centre of the driver's cabin.
Details further switches and pilot lamps on the right side of the cabin.
Lists and describes switches and pilot lamps on the left side of the cabin.
Details controls on the centre console, including joysticks and displays.
Describes audio systems and sockets in the rear partition of the cabin.
Details main control boxes, fuses, and diagnostic sockets for vehicle electrics.
Details the switches and warning lamps on the cabin pump control panel.
Describes the panther operator's display and its various screens and indications.
Explains the function of various pilot lamps like rotating beacons, shutter status, and warning lamps.
Lists and describes various valves, gauges, and indicators related to pump operation.
Introduces external control stations and lists their indications and controls.
Details emergency tools, control panels, and connections on the left side.
Lists and describes switches and pilot lamps on the left pump control panel.
Lists and describes controls and connections on the right hand side.
Describes additional installations in the pump compartment.
Explains the system for checking oil levels in the gearbox and priming pump.
Describes the visual indicators for water and foam compound tank content levels.
Details the 230 Volt AC terminal, fuses, battery box, and power supply socket.
Provides a checklist of pre-operation checks for safety and equipment readiness.
Explains the pneumatic operation, control functions, and locking mechanism of locker doors.
Refers to the chassis operation manual for starting drive engines.
Emphasizes the correct use of tow away adapters for towing the vehicle.
Details the alarm-start-device for starting engines remotely and its conditions.
Provides steps for safely shutting down the drive engines.
Explains how to engage the pump electronically and its indicators.
Details the procedure for disengaging the pump and its indicators.
Describes the RM 60 C roof turret, its design, and components.
Explains how the roof turret is controlled remotely via a handle.
Details operation of the roof turret with water and foam.
Explains how to temporarily and permanently stop turret operation.
Describes manual emergency operation of the roof turret if electric controls fail.
Describes the RM 15 C bumper turret, its design, and components.
Explains the joystick control elements for the bumper turret.
Details operation of the bumper turret with water and foam.
Explains how to stop the bumper turret operation.
Describes the oscillating mode of the bumper turret and its programming.
Details the operation of the undertruck nozzles for water and foam.
Explains how to operate the pump system manually when automatic mode fails.
Describes manual control of valves for turrets and nozzles during electric failure.
Details the stand-by operation procedure to protect the pump system from freezing.
Explains the procedure for operating the pump using tank suction.
Describes how to draft water from an open source, including cavitation warnings.
Details the procedure for operating the pump from a hydrant or supply line.
Provides critical safety warnings for pump operations, including water hammer and electrical hazards.
Explains how to perform foam operations using the internal tank or external container.
Advises on continuous monitoring of pump operation and immediate actions for potential dangers.
Provides the procedure for safely disengaging the pump system.
Details the procedure for operating handlines, including pressure adjustment and safety.
Describes the twin agent hose reel system, its operation, and safety precautions.
Covers operation with water and foam for the twin agent system.
Explains how to drain the hose reels using compressed air.
Details the process of filling the water tank using the vehicle's pump.
Describes filling the water tank using external supply lines.
Explains how to fill the foam tank using an external pump.
Details filling the foam tank using an electric pump.
Describes draining and transferring foam compound.
Explains the procedure for flushing the electric foam compound pump.
Details how to engage, lift, and control the light mast and flood lights.
Explains the procedure for safely shutting down and lowering the light mast.
Describes the dry powder units, hose reels, and associated controls.
Lists and explains the controls and indicators for the dry powder unit.
Details the procedure for operating the dry powder rapid intervention system.
Explains the pneumatic service unit and shut-off valve for the compressed air system.
Describes how to manually control pneumatic solenoids if electric control fails.
Explains manual operation of pneumatic actuators in case of air supply failure.
Describes manual adjustment of the foam proportioning rate if the motor fails.
Explains the automatic and manual flushing procedures for the pump system.
Provides procedures for draining the pump system and operating in cold climates.
Outlines general inspection procedures to ensure optimal vehicle reliability.
Details inspection points for the vehicle exterior, chassis, and superstructure.
Provides guidelines for inspecting tyre inflation, wear, and condition.
Covers inspection of cabin gauges, wipers, beacons, lights, horn, and brakes.
Provides guidelines for washing the vehicle, including water pressure and cleaning agents.
Details cleaning for chrome parts, upholstery, and films.
States that service and repair must be done by specialists according to intervals.
Details oil change procedures and oil level checks for the pump gearbox.
Details oil change procedures and oil recommendations for the priming pump.
Outlines yearly checks for valve plates and V-belts of the priming pump drive.
Covers periodic checks for propeller shafts and their lubrication.
Details draining condensate, cleaning the reservoir, and cleaning the filter cartridge.
Discusses battery capacity loss, charging procedures, and safety precautions.
Explains battery charging via socket and provides jump starting safety instructions.
Details inspection and maintenance procedures for the PP tanks.
Covers re-tightening chassis bolts, checking hollow protection, rust spots, and air dryer maintenance.
Explains how to check and maintain flexible mounting elements between body, tanks, and chassis.
Presents a comprehensive chart for lubrication, oil changes, and checks for various components.
Lists common pump problems, their probable causes, and corrective actions.
Outlines the schedule for testing electrical systems, alternators, and FI protection.
Provides guidance on the proper disposal of used parts and materials according to regulations.
To Next Page