EasyManuals Logo

Sanyo PLV-Z3000 Owner's Manual

Sanyo PLV-Z3000
60 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #27 background imageLoading...
Page #27 background image
27
Press the Point ed buttons to select the Image Menu and
press the Point
8 or OK buttons to access the submenu
items.
1
2
Use the Point ed buttons to select the desired image mode
and press the Point
8 or OK buttons. The selected item is
check marked.
Image Mode Selection
Direct Operation
Menu Operation
Remote Control
IMAGE MODE
buttons
Image mode selection can be made for each input source.
Image
Press the IMAGE MODE buttons (PRESET or USER) on the
remote control to select the desired image mode.
Press the PRESET button to select Brilliant cinema, Creative
cinema, Pure cinema, Natural, Living, Dynamic, or x.v.Color; press
the USER button to select User image 1 – 7.
You can also change the Image mode by pressing the PRESET
button or the USER button on the remote control for more than 1
second. When the PRESET button is pressed, the Preset submenu
with a check mark on the currently set image mode appears. When
the USER button is pressed, the User submenu with a check
mark on the currently set image mode appears. Use the Point
ed
buttons to select the desired image mode and press the Point
8 or
OK buttons. The selected item is check marked.
For viewing contrasty 3D images in a dark room.
Creative cinema
For viewing images with quiet tones of color and less gradation in
a dark room.
Pure cinema
For displaying user preset image mode in the Image adj. Menu
(pp.28 – 33).
User image 1 – 7
For viewing images faithfully reproduced without any control by
the projector in a dark room.
Natural
For viewing video sources such as sports or dramas from TV with
clear and contrasty images in a bright room.
Living
For viewing contrasty images in a bright room.
Dynamic
x.v.Color
Note:
•TheImageMenucannotbeoperatedwithoutaninputsignal.
•x.v.ColorcanbeselectedonlywhentheincomingsignalisHDMI1
orHDMI2(p.26).
•Brightness,Contrast,Color,Tint,Colortemp.,Red,Green,Blue,
Gamma,Progressive,Noisereduction,Autoblackstretch,Contrast
enhancement,Colormanagement,Dynamicgamma,Custom
gamma.intheImagemode(p.28)cannotbeadjustedwhen
x.v.Colorisselected.
For viewing movies in a brightish room.
Brilliant cinema
Brilliant cinema Creative cinema Pure cinema
Natural Living Dynamic x.v.Color
Brilliant cinema
• • • •
PRESET button
USER button
User image 1 User image 2 User image 3
User image 4 User image 5 User image 6
User image 7 User image 1
• • • •
Image Menu
Press the Point d button
to move on to the next
items.
The selected image mode.
“x.v.Color”isatrademarkofSonyCorporation.
This mode accepts x.v.Color (xvYCC) signal.

Other manuals for Sanyo PLV-Z3000

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Sanyo PLV-Z3000 and is the answer not in the manual?

Sanyo PLV-Z3000 Specifications

General IconGeneral
Matrix size0.7 \
Vertical scan range50 - 100 Hz
Horizontal scan range15 - 80 kHz
Projection technologyLCD
Contrast ratio (typical)-
Screen size compatibility40 - 300 \
Aspect ratio16:9
RS-232 ports1
Dimensions (WxDxH)400 x 146 x 346 mm
Lamp typeUHP
Lamp power165 W
Light source typeLamp
Service life of light source2000 h
Service life of light source (economic mode)3000 h
FocusManual
Focal length range22.3 - 45.3 mm
Noise level19 dB
Dot clock scanning frequency100 MHz
Serial interface typeRS-232
Component video (YPbPr/YCbCr) in3
Weight and Dimensions IconWeight and Dimensions
Weight7500 g

Related product manuals