Sartorius SIWABBP - Page 70

Signum 1-2-3
Classification Application W Classification Application
W
70
Minimum load
The minimum load for the first class is
configured in Setup under:
Appl:
W: 3.6.
Appl 2
:
Signum
®
3:
class
: 3.6.
Once the limit is exceeded by the load,
initialization can begin.
Once the application is initialized,
a weight value below the minimum
load is designated Class 0; no class is
displayed.
The minimum load required for
automatic taring of the container
weight on the platform (first weight),
or for automatic printout of results,
is configured in Setup under:
Appl:
W: 3.5.
Signum
®
3:
Appl: m.weigh: 3.5.
You can choose from the following
10 levels for this setting:
1 digit
2 digits
5 digits
10 digits
20 digits
50 digits
100 digits
200 digits
500 digits
1000 digits
The “digits” here refer to the scale
intervals in the connected weighing
platform. If the interval of the
connected platform is 1 g, for example,
and 1000 digits are required, you must
place at least 1000 g (=1000 intervals
=1000 digits) on the weighing platform
for the first class to activate autotaring
or autoprint.
Display
The result of a given measurement is
shown as either a weight value or a
class number.
– Weight display:
The current weight is shown in the
measured value line and the current
class in the text lines.
– Display of classes:
The current class is shown in the
measured value line, and the current
weight in the text lines.
Digital I/O
Interface
The Classification application supports
the digital input/output-interface.
There are 4 control lines, or outputs,
which are activated as follows (see also
the diagram below):
– With 3 classes:
– Class 1
– Class 2
– Class 3
– Set
– With 5 classes:
– Classes 1/2
– Classes 2/3/4
– Classes 4/5
– Set
In Setup, under:
Appl:
W: 4.7.
Signum
®
3:
Appl 2:
class: 4.7.
you can define whether these control
ports are
– switched off
– always on
– on at stability
The “SET” output normally changes
its voltage level when the current
weight exceeds the minimum load.
Alternatively, you can assign the
“Ready for use” function to this port.
Configured in Setup under:
Appl:
W: 4.3.
Signum
®
3:
Appl 2:
class: 4.3.
70
Minimum Load
The minimum load for the first class is
configured in Setup under:
Appl:
W: 3.6.
Appl 2
:
Signum
®
3:
class
: 3.6.
Once the limit is exceeded by the load,
initialization can begin.
Once the application is initialized, a
weight value below the minimum load
is designated Class 0; no class is
displayed.
The minimum load required for
automatic taring of the container
weight on the platform (first weight),
or for automatic printout of results,
is configured in Setup under:
Appl:
W: 3.5.
Signum
®
3:
Appl
: m.weigh: 3.5.
You can choose from the following
10 levels for this setting:
1 digit
2 digits
5 digits
10 digits
20 digits
50 digits
100 digits
200 digits
500 digits
1000 digits
The “digits" here refer to the scale
intervals in the connected weighing
platform. If the interval of the
connected platform is 1 g, for example,
and 1000 digits are required, you must
place at least 1000 g (=1000 intervals
=1000 digits) on the weighing platform
for the first class to activate autotaring
or autoprint.
Display
The result of a given measurement is
shown as either a weight value or a class
number.
– Weight display:
The current weight is shown in the
measured value line and the current
class in the text line.
– Display of classes:
The current class is shown in the
measured value line, and the current
weight in the text line.
Digital Input/Output Interface
The Classification application supports
the digital input/output-interface.
There are 4 control lines, or outputs,
which are activated as follows (see also
the diagram below):
– With 3 classes:
– Class 1
– Class 2
– Class 3
– Set
– With 5 classes:
– Classes 1/2
– Classes 2/3/4
– Classes 4/5
– Set
In Setup, under:
Appl:
W: 4.7.
Signum
®
3:
Appl 2
:
class: 4.7.
you can define whether these control
ports are
– switched off
– always on
– on at stability
The “SET” output normally changes its
voltage level when the current weight
exceeds the minimum load.
Alternatively, you can assign the “Ready
for use” function to this port.
Configured in Setup under:
Appl:
W: 4.3.
Signum
®
3:
Appl 2
:
class: 4.3.
Digital I/O Interface
Control lines when working with 3 classes
Digital I/O Interface
Control lines when working with 5 classes
Class
1
23
Min. load
Max. load
Class 2
Set
Class 1
Class 3
Operative
Class
1
2345
Min. load
Max. load
Set
Classes 1/2
Classes 4/5
Operative
Classes 2/3/4