SATO CG408 User Manual

Section 6: General Specifications
Page 6-2 CG4 Series Operator Manual
MODEL NAME
CG408 DT/ CG408TT CG412 DT/ CG412TT
MEDIA (BE SURE TO USE MEDIA MANUFACTURED OR CERTIFIED BY SATO)
Type
Direct Thermal / Thermal Transfer depending on print model (DT or TT)
Roll stock or Fan-fold
Wind Direction Roll stock: Face In or Face out winding
Roll and Core Diameter
Maximum outer diameter: 5.04” (128 mm) with Inner core diameter: 1.5” (40 mm)
* Inner core diameter: 0.75” (19.05 mm) with maximum outer diameter: 4.33” (110
mm) can be accepted, but there is no performance guarantee.
Fanfold Max. stack height 4.65” (118 mm) (external supply)
Size
Label
Continuous
Cutter
Dispenser
Tear-off
Linerless
Pitch : 0.27” to 11.8” (7 to 300 mm)
Pitch including liner : 0.39” to 11.93” (10 to 303 mm)
Width : 0.86” to 4.21” (22 to 107 mm)
Width including liner : 0.98” to 4.33” (25 to 110 mm)
Pitch : 0.87” to 11.8” (22 to 300 mm)
Pitch including liner : 0.98” to 11.93” (25 to 303 mm)
Width : 0.87” to 4.21” (22 to 107 mm)
Width including liner : 0.98” to 4.33” (25 to 110 mm)
Pitch : 0.87” to 3.93” (22 to 100 mm)
Pitch including liner : 0.98” to 4.05” (25 to 103 mm)
Width : 0.87” to 4.21” (22 to 107 mm)
Width including liner : 0.98” to 4.33” (25 to 110 mm)
Pitch : 0.87” to 11.8” (22 to 300 mm) *
1
Pitch including liner : 0.98” to 11.93” (25 to 303 mm)
Width : 0.87” to 4.21” (22 to 107 mm)
Width including liner : 0.98” to 4.33” (25 to 110 mm)
Pitch : 0.98” to 3.93” (25 to 100 mm) *
1
With : 0.98” to 4.33” (25 to 110 mm)
Non-adhesive paper
Continuous
Cutter
Tear-off
Pitch : 0.39” to 11.93” (10 to 303 mm) *
1
Width : 0.98” to 4.33” (25 to 110 mm)
Pitch : 0.98” to 11.93” (25 to 303 mm)
Width : 0.98” to 4.33” (25 to 110 mm)
Pitch : 0.98” to 11.93” (25 to 303 mm) *
1
Width : 0.98” to 4.33” (25 to 110 mm)
*
1
When using media with small pitch, you must tear it by hand.
• The above size may be limited by use conditions, such as type of paper, usage
environment, and application.
• When using the dispenser mode, restrictions apply to the maximum paper length
according to paper installation conditions.
Thickness 0.0024” to 0.0074” (0.06 to 0.19 mm)

SATO CG408 Specifications

General

Resolution	203 dpi
Max Print Width	104 mm
Print Method	Thermal Transfer
Max Print Speed	4 inches/sec
Media Roll Diameter	127 mm (5 inches)
Memory	4 MB Flash
Interface	USB, Serial, Ethernet
Media Sensor	Reflective and Transmissive
Media Thickness	0.06 mm - 0.19 mm
Ribbon Length	100 m (328 ft)
Label Thickness Range	0.06 mm - 0.19 mm